POWER WINDOW CONTROL SYSTEM Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION

When the power switch is on (IG), the power window regulator motor assembly RH (for rear RH door) is operated by the power window regulator switch assembly (for rear RH door).

WIRING DIAGRAM

A01HSMZE18

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) - AUXILIARY BATTERY)


    1. Disconnect the L6 power window regulator switch assembly (for rear RH door) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L6-3 (B) - Body ground Power switch on (IG) 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR)


    1. A01HUN9E19
      Text in Illustration
      *a

      Component without harness connected

      (Power Window Regulator Switch Assembly (for Rear RH Door))

      Remove the power window regulator switch assembly (for rear RH door) Click here.

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (D) - 2 (SD) UP Below 1 Ω
      3 (B) - 4 (U) Below 1 Ω
      1 (D) - 2 (SD) off Below 1 Ω
      4 (U) - 5 (SU) Below 1 Ω
      4 (U) - 5 (SU) DOWN Below 1 Ω
      1 (D) - 3 (B) Below 1 Ω

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR REAR RH DOOR) - POWER WINDOW REGULATOR MOTOR RH)


    1. Disconnect the L5 power window regulator motor assembly RH (for rear RH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L6-4 (U) - L5-1 (U) Always Below 1 Ω
      L6-1 (D) - L5-2 (D) Always Below 1 Ω
      L6-4 (U) - Body ground Always 10 kΩ or higher
      L6-1 (D) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. A01HV9VE74
      Text in Illustration
      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly)

      Remove the power window regulator master switch assembly Click here.

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      6 (B) - 10 (U) UP Below 1 Ω
      1 (E) - 18 (D) Below 1 Ω
      1 (E) - 10 (U) off Below 1 Ω
      1 (E) - 18 (D) Below 1 Ω
      6 (B) - 18 (D) DOWN Below 1 Ω
      1 (E) - 10 (U) Below 1 Ω

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR REAR RH DOOR)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K11-10 (U) - L6-5 (SU) Always Below 1 Ω
      K11-18 (D) - L6-2 (SD) Always Below 1 Ω
      K11-10 (U) - Body ground Always 10 kΩ or higher
      K11-18 (D) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR RH DOOR) Click here