POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

When the power switch is on (IG), the power window regulator motor assembly RH (for front passenger door) is operated by the power window regulator switch assembly (for front passenger door).

WIRING DIAGRAM

A01HSPTE10

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER DOOR) - AUXILIARY BATTERY)


    1. Disconnect the J11 power window regulator switch assembly (for front passenger door) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J11-3 (B) - Body ground Power switch on (IG) 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER DOOR)


    1. A01HUN9E19
      Text in Illustration
      *a

      Component without harness connected

      (Power Window Regulator Switch Assembly (for Front Passenger Door))

      Remove the power window regulator switch assembly (for front passenger door) Click here.

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (D) - 2 (SD) UP Below 1 Ω
      3 (B) - 4 (U) Below 1 Ω
      1 (D) - 2 (SD) off Below 1 Ω
      4 (U) - 5 (SU) Below 1 Ω
      4 (U) - 5 (SU) DOWN Below 1 Ω
      1 (D) - 3 (B) Below 1 Ω

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER DOOR) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR FRONT PASSENGER DOOR) - POWER WINDOW REGULATOR MOTOR RH)


    1. Disconnect the J14 power window regulator motor assembly RH (for front passenger door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J11-4 (U) - J14-2 (U) Always Below 1 Ω
      J11-1 (D) - J14-1 (D) Always Below 1 Ω
      J11-4 (U) - Body ground Always 10 kΩ or higher
      J11-1 (D) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. A01HV9VE72
      Text in Illustration
      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly)

      Remove the power window regulator master switch assembly Click here.

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      6 (B) - 16 (U) UP Below 1 Ω
      1 (E) - 15 (D) Below 1 Ω
      1 (E) - 16 (U) off Below 1 Ω
      1 (E) - 15 (D) Below 1 Ω
      6 (B) - 15 (D) DOWN Below 1 Ω
      1 (E) - 16 (U) Below 1 Ω

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR FRONT PASSENGER DOOR))


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K11-16 (U) - J11-5 (SU) Always Below 1 Ω
      K11-15 (D) - J11-2 (SD) Always Below 1 Ω
      K11-16 (U) - Body ground Always 10 kΩ or higher
      K11-15 (D) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR FRONT PASSENGER DOOR) Click here