CENTER AIRBAG SENSOR ASSEMBLY REMOVAL


  1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  2. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01HTTW

      Disengage the 10 claws and remove the front door scuff plate LH.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01HVSU

      Remove the clip.

    2. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01HSG5

      Disconnect the front door opening trim weatherstrip LH.

  6. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01HTFQ

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HT5Y

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01HUD8

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01HTGO

      Remove the bolt <C> and screw <D> or <E>.

    2. A01HSR5

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  9. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01HW3X

      Remove the 2 screws <D> or <E>.

    2. Open the lower instrument panel door.

    3. A01HTBU

      Remove the 3 screws <D> or <E>.

    4. A01HSJJ

      Disengage the 2 clips and 3 guides.

    5. A01HVHW

      Disengage the glove compartment light as shown in the illustration.

    6. Disconnect each connector and remove the lower instrument panel sub-assembly.

  10. REMOVE BOX BOTTOM MAT


    1. A01HURY

      Remove the box bottom mat.

  11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01HV5K

      Remove the 2 screws <D> or <E>.

    2. A01HV6V

      Disengage the 4 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  12. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A01HU69

      Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. A01HUWE

      Remove the 2 screws <D> or <E>.

    3. A01HU9N

      Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.

  13. REMOVE CONSOLE BOX INSERT


    1. A01HW6K

      Remove the 2 screws <D> or <E>.

    2. A01HSMD

      Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.

  14. REMOVE FLOOR CARPET BRACKET LH


    1. A01HT24

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket LH.

  15. REMOVE FLOOR CARPET BRACKET RH


    1. A01HUF5

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket RH.

  16. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    1. A01HTVM

      Remove the clip and the No. 1 console box duct.

  17. REMOVE AIRBAG SENSOR ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Turn back the carpet.

    4. A01HTIH

      Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Remove the 3 bolts and airbag sensor assembly.