CENTER AIRBAG SENSOR ASSEMBLY INSTALLATION

INSTALL AIRBAG SENSOR ASSEMBLY
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
3. Text in Illustration
  
  *a Fulcrum Length
  
  Using SST, install the airbag sensor assembly with the 3 bolts.
  
  SST
  
  09961-00950
  
  Torque:
  
  without SST
  
  18 N*m { 178 kgf*cm, 13 ft.*lbf }
  
  with SST
  
  11 N*m { 112 kgf*cm, 8 ft.*lbf }
  Note
  - Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
  - This torque value is effective when SST is parallel to a torque wrench.
  - If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
  - When installing the airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
  - When the power switch is first turned on (IG) after the airbag sensor assembly has been replaced, make sure that no one is in the vehicle.
4. Text in Illustration
  
  *1 Waterproof Sheet
  
  Connect the connectors to the airbag sensor assembly as shown in the illustration.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
5. Check that the waterproof sheet is properly set.
6. Check that there is no looseness in the installation parts of the airbag sensor assembly.
INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)
1. Install the No. 1 console box duct with the clip.
INSTALL FLOOR CARPET BRACKET LH
1. Engage the 2 guides.
2. Install the floor carpet bracket LH with the 2 clips.
INSTALL FLOOR CARPET BRACKET RH
1. Engage the 2 guides.
2. Install the floor carpet bracket RH with the 2 clips.
INSTALL FRONT NO. 2 CONSOLE BOX INSERT
1. Engage the 2 claws to connect the room temperature sensor.
2. Engage the clip and 3 guides.
3. Install the front No. 2 console box insert with the 2 screws <D> or <E>.
INSTALL CONSOLE BOX INSERT
1. Engage the clip and 3 guides.
2. Install the console box insert with the 2 screws <D> or <E>.
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
1. Connect each connector.
2. Engage the 4 clips and guide.
3. Install the upper console panel sub-assembly with the 2 screws <D> or <E>.
INSTALL BOX BOTTOM MAT
1. Install the box bottom mat.
INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
1. Connect each connector.
2. Engage the glove compartment light as shown in the illustration.
3. Engage the 3 guides and 2 clips.
4. Install the lower instrument panel sub-assembly with the 5 screws <D> or <E>.
INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY
1. Engage the 4 claws, 9 clips and 3 guides.
2. Install the lower No. 1 instrument panel finish panel assembly with the bolt <C> and screw <D> or <E>.
CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
INSTALL INSTRUMENT SIDE PANEL LH
1. Engage the 3 guides.
2. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
1. Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.
2. Install the cowl side trim sub-assembly LH with the clip.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Engage the 10 claws to install the front door scuff plate LH.
INSTALL REAR CONSOLE BOX ASSEMBLY

Click here
INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here
PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION
Tech Tips
- When the airbag sensor assembly is replaced, perform zero point learning for the yaw rate and acceleration sensor Click here.
- The yaw rate and acceleration sensor is built into the airbag sensor assembly.