FRONT SEAT ASSEMBLY (for Power Seat) REASSEMBLY


  1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY


    1. Install the separate type front seat cushion spring assembly.

  2. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Driver Side)


    1. Install the 2 front seatback hooks to the lumbar support adjuster assembly.

    2. A01HUOM

      Engage the 2 guides.

    3. Engage the 4 claws to install the lumbar support adjuster assembly.

    4. Connect the connector.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (for Front Passenger Side)


    1. Install the 2 front seatback hooks to the separate type front seatback spring assembly.

    2. A01HUM4

      Engage the 2 guides.

    3. Engage the 4 claws to install the separate type front seatback spring assembly.

  4. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY


    1. Install the front seatback frame sub-assembly with the 4 bolts.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

  5. INSTALL FRONT SEAT CUSHION PANEL SUB-ASSEMBLY (for Driver Side)


    1. Install the front seat cushion panel sub-assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  6. INSTALL FRONT UPPER SEAT TRACK COVER LH


    1. Engage the 2 claws to install the front upper seat track cover LH.

  7. INSTALL FRONT UPPER SEAT TRACK COVER RH


    1. Engage the 2 claws to install the front upper seat track cover RH.

  8. INSTALL REAR UPPER SEAT TRACK COVER LH (for Front Passenger Side)


    1. Engage the 2 claws to install the rear upper seat track cover LH.

  9. INSTALL REAR UPPER SEAT TRACK COVER RH (for Front Passenger Side)


    1. Engage the 2 claws to install the rear upper seat track cover RH.

  10. INSTALL FRONT NO. 2 SEAT WIRE


    1. Connect each connector and engage each wire harness clamp to install the front No. 2 seat wire.

  11. INSTALL FRONT SEAT WIRE


    1. Connect each connector and engage each wire harness clamp to install the front seat wire.

  12. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side)


    1. A01HTRM

      Engage the claw to install the occupant detection ECU.

      Note

      If the occupant detection ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the occupant detection ECU with a new one.

    2. Connect the 2 connectors.

      Note

      When installing the occupant detection ECU, be careful that the SRS wiring does not interfere with or is pinched between other parts.

  13. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)


    1. Engage the clamp to install the seat heater control sub-assembly.

    2. Connect the connector.

  14. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)


    1. A01HUDY

      Engage the 2 claws to install the front seat lower cushion shield LH.

    2. Engage the hook as shown in the illustration.

    3. Install the screw.

      Torque:
      0.6 N*m  { 6 kgf*cm, 5 in.*lbf }

  15. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)


    1. A01HW46

      Engage the 2 claws to install the front seat lower cushion shield RH.

    2. Engage the hook as shown in the illustration.

    3. Install the screw.

      Torque:
      0.6 N*m  { 6 kgf*cm, 5 in.*lbf }

  16. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Front Passenger Side)


    1. Engage the 2 claws to install the front seat lower cushion shield LH.

  17. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Front Passenger Side)


    1. Engage the 2 claws to install the front seat lower cushion shield RH.

  18. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)


    1. Using a tacker, install the front seatback heater assembly to the separate type front seatback cover with 8 new tag pins.

  19. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A01HT84

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    2. Engage the 2 fasteners.

  20. INSTALL FRONT SEAT AIRBAG ASSEMBLY

    CAUTION:


    • The nuts must not be reused.

    • Make sure that the front seatback frame sub-assembly or separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.


    1. Install the front seat airbag assembly with 2 new nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Engage the 2 clamps.

  21. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Temporarily install the separate type front seatback cover with pad.

    2. Engage the 4 claws to install the 2 front seat headrest supports.

    3. Engage the 2 hooks.

      CAUTION:


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after engage the 2 hooks.

      • Engage the 2 hooks securely.


      1. Slide each hook to engage them.

      2. Install the 4 clips.

    4. Engage the 2 fasteners.

    5. Engage the hook.

  22. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    1. Using a tacker, install the front seat cushion heater assembly to the separate type front seat cushion cover with 20 new tag pins.

  23. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01HTYI

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 12 new hog rings.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

  24. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Temporarily install the separate type front seat cushion cover with pad.

    2. Engage each hook.

    3. for Driver Side:


      1. A01HUV4

        Install the separate type front seat cushion cover.

    4. for Front Passenger Side:


      1. A01HV36

        Install the separate type front seat cushion cover.

    5. A01HV9UE01

      Engage the claw (D) and 3 clamps (C) to install the front seat airbag assembly wire harness.

    6. Engage the clamp (B).

    7. Connect the connector (A).

    8. w/ Seat Heater System:


      1. Connect the connector (E).

      2. Engage the clamp (F).

  25. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)


    1. A01HTAME01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part of the front seat adjuster.

    2. Engage the clamp.

    3. Engage each clamp under the front seat assembly.

  26. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)


    1. A01HTG1E01
      Text in Illustration
      *1 Protruding Part
      *2 Limit Switch

      Install the front seat inner belt assembly RH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part of the front seat adjuster.

    2. Connect the limit switch with the screw.

    3. Connect the connector.

  27. INSTALL FRONT SEAT INNER CUSHION SHIELD


    1. Install the front seat inner cushion shield with the 2 screws.

      Torque:
      0.6 N*m  { 6 kgf*cm, 5 in.*lbf }

  28. INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side)


    1. Connect the connector to install the front lumbar power seat switch.

  29. INSTALL FRONT POWER SEAT SWITCH


    1. Install the front power seat switch to a new front seat cushion shield with the 3 screws.

  30. INSTALL FRONT SEAT CUSHION SHIELD


    1. for Driver Side:


      1. Engage the 4 claws to install the front lumbar power seat switch to the front seat cushion shield.

    2. Connect the front power seat switch connector.

    3. Engage the wire harness clamp.

    4. Engage the 2 claws to install the front seat cushion shield.

    5. Install the screw.

      Torque:
      0.6 N*m  { 6 kgf*cm, 5 in.*lbf }

  31. CONNECT SEPARATE TYPE FRONT SEATBACK COVER


    1. Connect the 2 rubber bands of the separate type front seatback cover.

  32. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. Engage the 4 claws to install the reclining power seat switch knob.

  33. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. Engage the 4 claws to install the slide and vertical power seat switch knob.

  34. INSTALL SEAT ADJUSTER COVER CAP


    1. Install the 2 seat adjuster cover caps.