SMART KEY SYSTEM (for Start Function) Power Source Mode does not Change to ON (ACC)

DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the power management control ECU receives a signal and changes the power source mode.

Tech Tips

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

WIRING DIAGRAM

A01HTR1E02

INSPECTION PROCEDURE

Note


  • When using the Techstream with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and vehicle begins, or 2) connect the Techstream to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

    for Power Source Control: Body Electrical / Power Source Control / DTC.

    for Smart Key: Body Electrical / Smart Key / DTC.

  • The smart key system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

  • Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart Click here.

  • If the smart key system is disabled through the customize function, enable the system before performing troubleshooting Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • After completing repairs, confirm that the problem does not occur.

Tech Tips

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (ACC) but does change to on (IG)

    Power Source Control

  • Power Supply Condition

  • ACC Relay Monitor

 -

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the I4 connector from the power management control ECU.

    2. Disconnect the 3B connector from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I4-1 (ACCD) - 3B-23 Always Below 1 Ω
      3B-7 - Body ground Always Below 1 Ω
      I4-1 (ACCD) or 3B-23 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly Click here.

      A01HUZZE01
      Text in Illustration
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly Click here.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition

      • 3E-1 - 3B-37

      • 3E-1 - 3B-10

      		 Auxiliary battery voltage not applied to terminals 3B-23 and 3B-7 10 kΩ or higher
      Auxiliary battery voltage applied to terminals 3B-23 and 3B-7 Below 1 Ω

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    OK

  3. INSPECT POWER MANAGEMENT CONTROL ECU

    A01HVBIE15
    Text in Illustration
    *a

    Component with harness connected

    (Power Management Control ECU)

    1. Reconnect the I4 power management control ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I4-1 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher

    NG

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    OK

    CHECK RELAY CONTACT SIDE CIRCUIT