REAR CROSS TRAFFIC ALERT BUZZER INSTALLATION

INSTALL BLIND SPOT MONITOR BUZZER
1. Connect the connector.
2. Engage the 3 clamps to install the blind spot monitor buzzer.
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
2. Engage the 5 guides and 3 clips to install the package tray trim panel assembly.
INSTALL REAR SEAT SHOULDER BELT COVER
1. Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.
  
  Tech Tips
  
  Use the same procedure for the other 2 rear seat shoulder belt covers.
INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER
1. Engage the 2 guides and 2 claws to install the child restraint seat tether anchor cover.
  
  Tech Tips
  
  Use the same procedure for the other 2 child restraint seat tether anchor covers.
INSTALL CENTER STOP LIGHT SET
1. Connect the connector.
2. Temporarily install the center stop light set.
3. Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.
CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
1. Text in Illustration
  
  *1 Protruding Part
  
  Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  Note
  - Install the rear seat inner with center belt assembly LH with the arrow on the anchor part facing the front of the vehicle.
  - Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
1. Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.
  
  Torque:
  
  18 N*m { 184 kgf*cm, 13 ft.*lbf }
CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)
1. Text in Illustration
  
  *1 Protruding Part
  
  Connect the floor anchor of the rear seat outer belt assembly with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)
1. Text in Illustration
  
  *1 Protruding Part
  
  Connect the floor anchor of the rear seat outer belt assembly with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
INSTALL ROOF SIDE INNER GARNISH LH
1. Engage the guide.
2. Engage the 5 clips to install the roof side inner garnish LH.
INSTALL ROOF SIDE INNER GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
1. Text in Illustration
  
  *1 Alignment Mark (Pink)
  
  Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *1 Alignment Mark (Blue)
  
  Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL REAR SIDE SEATBACK ASSEMBLY LH
1. Engage the hook to install the rear side seatback assembly LH.
2. Install the 2 bolts.
  
  Torque:
  
  18 N*m { 184 kgf*cm, 13 ft.*lbf }
3. Connect the connector.
4. Connect the rear seat outer belt to the rear seat shoulder belt guide LH.
INSTALL REAR SIDE SEATBACK ASSEMBLY RH
1. Engage the hook to install the rear side seatback assembly RH.
2. Install the 2 bolts.
  
  Torque:
  
  18 N*m { 184 kgf*cm, 13 ft.*lbf }
3. Connect the connector.
4. Connect the rear seat outer belt to the rear seat shoulder belt guide RH.
INSTALL REAR SEATBACK ASSEMBLY LH
1. Place the rear seatback assembly LH in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Install the rear seatback assembly LH with the 2 bolts.
  
  Torque:
  
  18 N*m { 184 kgf*cm, 13 ft.*lbf }
3. Connect the rear seat inner with center belt assembly LH to the rear seat center shoulder belt guide.
INSTALL NO. 2 ROOM PARTITION COVER
1. Engage the guide and claw to install the No. 2 room partition cover.
INSTALL REAR SEAT CUSHION LOCK HOOK
1. Engage the claw to install a new rear seat cushion lock hook.
  
  Note
  
  Rear seat cushion lock hooks must not be reused.
  
  Tech Tips
  
  Use the same procedure for the RH side and the LH side.
INSTALL REAR SEAT CUSHION ASSEMBLY
1. Place the rear seat cushion assembly in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.
3. Confirm that the seat cushion is firmly installed.
  
  Note
  
  When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.
CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL LUGGAGE TRIM SERVICE HOLE COVER
1. Engage the claw to connect the luggage trim service hole cover.
INSPECT SRS WARNING LIGHT

Click here