NAVIGATION SYSTEM (for Navigation Receiver Type), Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. DTC Detection Condition Trouble Area
B15C3 A short is detected in the speaker output circuit.

  • Harness or connector

  • Speaker

  • DCM (telematics transceiver)*1

  • Stereo component amplifier assembly

WIRING DIAGRAM

A01HTZSE02
A01HUFME02

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR


    1. Disconnect the connectors from the stereo component amplifier assembly, DCM (telematics transceiver)*1 and speakers.


      • *1: w/ Manual (SOS) Switch

    2. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I68-15 (FR+) - Body ground Always 10 kΩ or higher
      I68-30 (FR-) - Body ground Always 10 kΩ or higher
      I68-11 (FL+) - Body ground Always 10 kΩ or higher
      I68-26 (FL-) - Body ground Always 10 kΩ or higher
      I68-12 (TWR+) - Body ground Always 10 kΩ or higher
      I68-27 (TWR-) - Body ground Always 10 kΩ or higher
      I68-14 (TWL+) - Body ground Always 10 kΩ or higher
      I68-29 (TWL-) - Body ground Always 10 kΩ or higher
      I68-13 (CTR+) - Body ground Always 10 kΩ or higher
      I68-28 (CTR-) - Body ground Always 10 kΩ or higher
      I68-10 (SR+) - Body ground Always 10 kΩ or higher
      I68-25 (SR-) - Body ground Always 10 kΩ or higher
      I68-9 (SL+) - Body ground Always 10 kΩ or higher
      I68-24 (SL-) - Body ground Always 10 kΩ or higher
      I68-8 (WF1+) - Body ground Always 10 kΩ or higher
      I68-23 (WF1-) - Body ground Always 10 kΩ or higher

    3. w/ Manual (SOS) Switch

      Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I135-5 (SPO+) - Body ground Always 10 kΩ or higher
      I135-6 (SPO-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. A01HVFEE40
      Text in Illustration
      *A for RH
      *B for LH
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Resistance check


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        J5-1 (+) - J5-2 (-) Always 4.6 to 6.6 Ω
        K5-1 (+) - K5-2 (-) Always 4.6 to 6.6 Ω

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  3. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. A01HSQEE19
      Text in Illustration
      *A for RH
      *B for LH
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Resistance check


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I84-4 - I84-3 Always 3.4 to 5.2 Ω
        I2-4 - I2-3 Always 3.4 to 5.2 Ω

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  4. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. A01HSYRE14
      Text in Illustration
      *a

      Component without harness connected

      (Front No. 3 Speaker Assembly)

      Resistance check


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I60-1 - I60-2 Always 6.8 to 10.2 Ω

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

  5. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. A01HSYRE15
      Text in Illustration
      *A for RH
      *B for LH
      *a

      Component without harness connected

      (Rear No. 2 Speaker Assembly)

      Resistance check


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        O19-1 - O19-2 Always 6.8 to 10.2 Ω
        O20-1 - O20-2 Always 6.8 to 10.2 Ω

    NG

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    OK

  6. INSPECT REAR SPEAKER ASSEMBLY


    1. A01HVFEE35
      Text in Illustration
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Resistance check


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        O22-1 - O22-2 Always 4.8 to 6.8 Ω

    2. Proceed to the next step based on the inspection result.

      Result
      Condition Proceed to
      OK (w/ Manual (SOS) Switch) A
      OK (w/o Manual (SOS) Switch) B
      NG C

    B

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

    C

    REPLACE REAR SPEAKER ASSEMBLY Click here

    A

  7. INSPECT DCM (TELEMATICS TRANSCEIVER)


    1. A01HV4PE16
      Text in Illustration
      *a

      Component without harness connected

      (DCM (Telematics Transceiver))

      Resistance check


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I135-2 (SPI+) - I135-5 (SPO+) Always Below 1 Ω
        I135-3 (SPI-) - I135-6 (SPO-) Always Below 1 Ω
        I135-2 (SPI+) - I135-3 (SPI-) Always 10 kΩ or higher
        I135-5 (SPO+) - I135-6 (SPO-) Always 10 kΩ or higher
        I135-2 (SPI+) - Body ground Always 10 kΩ or higher
        I135-3 (SPI-) - Body ground Always 10 kΩ or higher

    NG

    REPLACE DCM (TELEMATICS TRANSCEIVER) Click here

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here