INSTRUMENT PANEL SPEAKER REMOVAL


  1. PRECAUTION (for 10 Speakers)

    Note

    except Radio and Display Type without Intuitive Parking Assist System:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP


    1. A01HSG5

      Disconnect the front door opening trim weatherstrip LH.

  3. REMOVE FRONT PILLAR GARNISH


    1. A01HUUHE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. A01HV4OE01

      While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (1) shown in the illustration, disengage the front pillar garnish clip.

    3. Pull the garnish in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. A01HUQIE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  4. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01HV6EE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HUYJ

      Using a moulding remover, disengage the 2 clips and 3 claws.

    3. Disengage the 2 guides to remove the No.1 instrument panel speaker panel sub-assembly.

  5. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    1. A01HVU7

      Remove the 2 screws.

    2. A01HVKI

      Lift the front No. 2 speaker assembly and disconnect the connector to remove the speaker.

      Note

      Do not touch the speaker cone.

  6. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for 10 Speakers)

    except Radio and Display Type without Intuitive Parking Assist System: Click here

  7. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (for 10 Speakers)

    Note

    except Radio and Display Type without Intuitive Parking Assist System:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. REMOVE REAR CONSOLE BOX ASSEMBLY (for 10 Speakers)

    Click here

  9. REMOVE BOX BOTTOM MAT (for 10 Speakers)


    1. A01HURY

      Remove the box bottom mat.

  10. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (for 10 Speakers)


    1. A01HV5K

      Remove the 2 screws <D> or <E>.

    2. A01HV6V

      Disengage the 4 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  11. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for 10 Speakers)


    1. A01HW8T

      Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

    2. A01HSUT

      Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

    3. A01HVNV

      Disengage the 3 claws and 2 clips as shown in the illustration.

    4. A01HSZ6

      Disengage the clamp.

    5. Disconnect the connector to remove the center instrument cluster finish panel assembly.

  12. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (for 10 Speakers)


    1. A01HTS7

      Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 6 clips to remove the No. 2 instrument panel register assembly.

  13. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for 10 Speakers)

    for Radio and Display Type: Click here

  14. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for 10 Speakers)

    for Navigation Receiver Type: Click here

  15. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY (for 10 Speakers)


    1. A01HV7C

      Disengage the 8 clips as shown in the illustration.

    2. Disconnect the connector to remove the No. 1 speaker opening cover assembly.

  16. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)


    1. A01HVJB

      Remove the 2 screws.

    2. A01HVS4

      Lift the front No. 3 speaker assembly and disconnect the connector to remove the speaker.

      Note

      Do not touch the speaker cone.