STEERING WHEEL INSTALLATION

Note


  • Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the auxiliary battery connected and the power switch on (IG).

  • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


  1. INSTALL STEERING SHAKE DAMPER


    1. Install the steering shake damper to the steering wheel sub-assembly with the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

  2. INSTALL CRUISE CONTROL SWITCH WIRE


    1. Install the cruise control switch wire.

  3. INSTALL CRUISE CONTROL MAIN SWITCH


    1. Connect the connector.

    2. A01HTDA

      Install the cruise control switch main with the 2 screws shown in the illustration.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

  4. INSTALL STEERING PAD SWITCH ASSEMBLY


    1. Engage the claw and 2 pins to install the steering pad switch assembly (RH side) to the steering wheel sub-assembly.

    2. Install the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

    3. Engage the claw and 2 pins to install the steering pad switch assembly (LH side) to the steering wheel sub-assembly.

    4. Install the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

    5. Connect the steering pad switch connector to the spiral cable sub-assembly.

    6. A01HV6G

      Pass the wire harness over the 2 guides.

  5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  6. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01HVKLE01

      Check if the spiral cable with sensor sub-assembly is centered.

      Text in Illustration
      A01HTJK Colored Part

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the part indicated by A is positioned at the top and the colored part shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.


      1. A01HUKG

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

        Text in Illustration
        A01HTTN Interlock

        Note


        • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

      2. A01HTS8

        Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the colored part shown in the illustration is visible.

        Text in Illustration
        A01HTJK Colored Part
        A01HTTN Interlock

        Tech Tips

        The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  7. INSTALL STEERING WHEEL ASSEMBLY


    1. A01HT2HE01
      Text in Illustration
      *a Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  8. CHECK STEERING WHEEL CENTER POINT

  9. INSTALL HORN BUTTON ASSEMBLY

    Click here