STEERING COLUMN ASSEMBLY INSTALLATION


  1. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A01HTD2E01
      Text in Illustration
      *a Matchmark

      Install the steering intermediate shaft assembly to the steering column assembly.

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  2. INSTALL STEERING POST ASSEMBLY


    1. Install the steering post assembly with the 4 nuts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

    2. Install the ground wire with the bolt.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }

    3. Engage the clamp.

    4. Connect the 2 connectors.

    5. Connect the connectors and engage the wire harness clamps to the steering post assembly.

  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


    1. Engage the 2 claws and guide to install the No. 2 air duct sub-assembly.

  4. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A01HVK3E01
      Text in Illustration
      *a Matchmark

      Connect the steering intermediate shaft assembly to the steering link assembly.

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering link assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }
    3. A01HVN7

      Tighten the clamp.

  5. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.

    2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  6. INSTALL UPPER STEERING COLUMN COVER


    1. Engage the 2 claws to install the upper steering column cover.

    2. Engage the 4 clips and 2 guides to the upper steering column cover.

  7. INSTALL LOWER STEERING COLUMN COVER


    1. A01HUI1

      Engage the 2 claws to install the lower steering column cover.

    2. A01HUKN

      Install the 2 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }
    3. A01HVGI

      Engage the claw.

  8. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  9. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01HVKLE01

      Check if the spiral cable with sensor sub-assembly is centered.

      Text in Illustration
      A01HTJK Colored Part

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the part indicated by A is positioned at the top and the colored part shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.


      1. A01HUKG

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

        Text in Illustration
        A01HTTN Interlock

        Note


        • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

      2. A01HTS8

        Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the colored part shown in the illustration is visible.

        Text in Illustration
        A01HTJK Colored Part
        A01HTTN Interlock

        Tech Tips

        The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  10. INSTALL STEERING WHEEL ASSEMBLY


    1. A01HT2HE01
      Text in Illustration
      *a Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  11. INSPECT STEERING WHEEL CENTER POINT

  12. INSTALL HORN BUTTON ASSEMBLY

    Click here

  13. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  14. INSTALL FRONT WHEEL LH

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }

  15. ADJUST PARKING ASSIST MONITOR SYSTEM (w/ Parking Assist Monitor System)

    Click here