ELECTRONICALLY CONTROLLED BRAKE SYSTEM Brake Warning Light Remains ON

DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light / red (malfunction) remains on:


WIRING DIAGRAM

A01HW0SE02

INSPECTION PROCEDURE

Note

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve Click here.

PROCEDURE


  1. CHECK DTC


    1. Check if ABS, VSC and/or electronically controlled brake system DTCs are output Click here.

      Result
      Result Proceed to
      DTC is not output. A
      DTC is output. B

    B

    REPAIR CIRCUITS INDICATED BY OUTPUT DTCS Click here

    A

  2. CHECK CAN COMMUNICATION SYSTEM


    1. Check if a CAN communication system DTC is output Click here.

      Result
      Result Proceed to
      DTC is not output. A
      DTC is output. B

    B

    INSPECT CAN COMMUNICATION SYSTEM Click here

    A

  3. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED


    1. Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

      OK
      The connector is securely connected.

    NG

    CONNECT CONNECTOR TO ECU CORRECTLY

    OK

  4. CHECK AUXILIARY BATTERY


    1. Check the auxiliary battery voltage.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Auxiliary battery Power switch on (IG) 11 to 14 V
      Auxiliary battery Power switch on (READY) 11 to 15.5 V

    NG

    CHARGE OR REPLACE AUXILIARY BATTERY

    OK

  5. CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)


    1. A01HUR5E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

      Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A28-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

    OK

  6. CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    1. A01HV5JE93
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

      Turn the power switch off.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A28-28 (GND) - Body ground Always Below 1 Ω
      A28-27 (GND2) - Body ground Always Below 1 Ω
      A28-26 (GND3) - Body ground Always Below 1 Ω
      A28-25 (GND4) - Body ground Always Below 1 Ω
      A28-24 (GND5) - Body ground Always Below 1 Ω
      A28-23 (GND6) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

    OK

  7. READ VALUE USING TECHSTREAM (PARKING BRAKE SWITCH ASSEMBLY)


    1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    2. Connect the Techstream to the DLC3.

    3. Turn the power switch on (IG).

    4. Select the Data List on the Techstream Click here.

      ABS/VSC/TRAC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Parking Brake SW Parking brake switch assembly / ON or OFF

      ON: Parking brake applied

      OFF: Parking brake released

      		 -

    5. Using the Techstream, check if the switch condition on the Techstream changes according to parking brake operation.

      OK
      The Techstream displays ON or OFF according to parking brake operation.

    NG

    INSPECT PARKING BRAKE SWITCH ASSEMBLY Click here

    OK

  8. INSPECT COMBINATION METER ASSEMBLY


    1. Turn the power switch off.

    2. Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream Click here.

    3. Check the combination meter assembly.

      OK
      The brake warning light / red (malfunction) turns on or off in accordance with Techstream operation.

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part Click here.


    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here

  9. INSPECT PARKING BRAKE SWITCH ASSEMBLY


    1. A01HT0EE03
      Text in Illustration
      *a

      Component without harness connected

      (Parking Brake Switch Assembly)

      Turn the power switch off.

    2. Disconnect the parking brake switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 (+) - Body ground

      Parking brake switch assembly ON

      (Switch pin free)

      		 Below 1 Ω
      1 (+) - Body ground

      Parking brake switch assembly OFF

      (Switch pin pushed in)

      		 10 kΩ or higher

    NG

    REPLACE PARKING BRAKE SWITCH ASSEMBLY Click here

    OK

  10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - PARKING BRAKE SWITCH ASSEMBLY)


    1. Disconnect the main body ECU (multiplex network body ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3D-20 (PKB) - A42-1 (+) Always Below 1 Ω
      3D-20 (PKB) - Body ground Always 10 kΩ or higher

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part Click here.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here