REAR SUSPENSION MEMBER REMOVAL


  1. REMOVE REAR WHEELS

  2. REMOVE CENTER EXHAUST PIPE ASSEMBLY

    Click here

  3. REMOVE NO. 2 FLOOR UNDER COVER


    1. A01HVDN

      Remove the 2 bolts and 2 clips.

      Text in Illustration
      A01HUVJ Bolt
      A01HUJP Nut (attached to under cover)

    2. Disengage the 3 nuts and remove the No. 2 floor under cover.

  4. REMOVE NO. 1 FLOOR UNDER COVER


    1. A01HVB3

      Remove the 2 bolts.

      Text in Illustration
      A01HUVJ Bolt
      A01HUJP Nut (attached to under cover)

    2. Disengage the 3 nuts and 2 clips, and remove the No. 1 floor under cover.

  5. REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET


    1. A01HW76

      Remove the 2 bolts and No. 3 exhaust pipe support bracket from the rear suspension member sub-assembly.

  6. REMOVE REAR SUSPENSION MEMBER DAMPER


    1. A01HUW9

      Remove the 2 bolts and rear suspension member damper from the rear suspension member sub-assembly.

      Text in Illustration
      A01HUJP Front of the Vehicle

  7. SEPARATE REAR STABILIZER LINK ASSEMBLY LH


    1. A01HVWR

      Remove the nut and separate the rear stabilizer link assembly LH from the rear stabilizer bar.

      If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.

  8. SEPARATE REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  9. REMOVE REAR STABILIZER BAR


    1. A01HSV9

      Remove the 4 bolts, rear stabilizer bar, 2 rear No. 1 stabilizer bar brackets, 2 rear No. 2 stabilizer bar brackets and 2 rear stabilizer bushings from the rear suspension member sub-assembly.

  10. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

    Click here

  11. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. A01HUT3

      Remove the bolt and nut, and separate the rear No. 2 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.

      Note

      When removing the bolt, keep the nut from rotating.

  12. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  13. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. A01HU4B

      Remove the bolt and rear No. 2 suspension arm assembly from the rear suspension member sub-assembly.

  14. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  15. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. A01HUW6

      Remove the bolt and nut, and separate the rear No. 1 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.

      Note

      When removing the bolt, keep the nut from rotating.

  16. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  17. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. A01HU4YE01
      Text in Illustration
      *1 Engine Lifter
      *2 Attachment
      A01HVUW Attachment Placement Location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

      Note


      • Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

      • Use the attachments to keep the rear suspension member sub-assembly level.

    2. Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stopper sub-assemblies and 2 rear suspension member lower stoppers.

      A01HVH7

    3. Slowly lower the rear suspension member sub-assembly.

      Note

      When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

  18. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. A01HSKZ

      Remove the bolt and rear No. 1 suspension arm assembly from the rear suspension member sub-assembly.

  19. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  20. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH


    1. A01HTBAE01

      Using SST and a press, remove the rear suspension member body mounting front cushion LH from the rear suspension member sub-assembly.

      SST
      09527-17011
      09950-60010   ( 09951-00340 )
      09950-70010   ( 09951-07100 )

  21. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

    Tech Tips

    Perform the same procedure as the LH side.

  22. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)


    1. A01HSKBE01

      Using SST and a press, remove the rear suspension member body mounting rear cushion from the rear suspension member sub-assembly.

      SST
      09527-17011
      09950-60010   ( 09951-00340 )
      09950-70010   ( 09951-07100 )

  23. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

    Tech Tips

    Perform the same procedure as the LH side.

  24. REMOVE HOLE PLUG


    1. A01HTH0

      Remove the 4 hole plugs from the rear suspension member sub-assembly.