RADIATOR INSTALLATION


  1. INSTALL RADIATOR ASSEMBLY


    1. A01HUE6E01
      Text in Illustration
      *a Guide

      Install the fan assembly to the radiator with the 2 guides at the bottom and 3 claws on the top.

    2. Install the 2 lower radiator supports to the radiator assembly.

    3. A01HV3R

      Install the radiator with fan assembly.

      Note

      Do not apply any excessive force to the radiator assembly (for inverter coolant), cooler condenser assembly or pipe when installing the radiator assembly.

    4. Install the radiator with fan assembly to the condenser assembly and radiator assembly (for inverter coolant) with the 4 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    5. Connect the No. 4 inverter cooling hose with the clamp.

    6. Connect the connector and the 2 clamps.

    7. Connect the 2 clamps.

  2. INSTALL UPPER RADIATOR SUPPORT


    1. Install the 2 radiator support cushions to the radiator assembly.

    2. Install the upper radiator support with the 5 bolts and connect the hood lock control cable clamp to the upper radiator support.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    3. Connect the 2 connectors.

  3. INSTALL HOOD LOCK ASSEMBLY


    1. A01HUXH

      Apply MP grease to the sliding areas of the lock.

    2. Connect the hood lock control cable assembly.

    3. Install the hood lock assembly with the 3 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    4. w/ Engine Hood Courtesy Switch:


      1. Connect the connector.

  4. CONNECT NO. 1 INVERTER COOLING PIPE ASSEMBLY


    1. A01HSKJE01

      Temporarily install the bolt A.

    2. Install the bolt B.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    3. Fully tighten the bolt A.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  5. CONNECT NO. 2 RADIATOR HOSE


    1. Connect the No. 2 radiator hose and clamp.

  6. CONNECT NO. 1 RADIATOR HOSE


    1. Connect the No. 1 radiator hose.

  7. INSTALL RADIATOR RESERVE TANK ASSEMBLY


    1. Install the radiator reserve tank with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Connect the radiator reserve tank hose.

  8. INSTALL NO. 5 INVERTER BRACKET


    1. Temporarily install the No. 5 inverter bracket with the 2 bolts.

    2. A01HV2LE01

      Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  9. INSTALL INLET AIR CLEANER ASSEMBLY


    1. Install the inlet air cleaner assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  10. INSTALL RADIATOR GRILLE SUB-ASSEMBLY


    1. A01HV3W

      Engage the 8 claws to install the radiator grille sub-assembly.

    2. Install the 3 clips.

  11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSTALL LUGGAGE TRIM SERVICE HOLE COVER


    1. Engage the claw to connect the luggage trim service hole cover.

  13. ADD COOLANT (for Engine)


    1. Tighten the radiator drain cock plug by hand.

    2. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

      Item Capacity
      Engine coolant 7.2 liters (7.6 US qts, 6.3 Imp. qts)

      Note

      Never use water as a substitute for engine coolant.

      Tech Tips

      TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    3. Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.

    4. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.

      If the coolant level is low, add coolant.

    5. Install the radiator cap sub-assembly and reserve tank cap.

    6. Put the engine in inspection mode Click here.

    7. Bleed air from the cooling system.

      Note


      • Before starting the engine, turn the A/C switch off.

      • Adjust the heater control to the maximum hot setting.

      • Adjust the blower speed to the low setting.


      1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

        Tech Tips

        The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

      2. Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

        CAUTION:

        When squeezing the radiator hoses:


        • Wear protective gloves.

        • Be careful as the radiator hoses are hot.

        • Keep your hands away from the cooling fans.

        Note


        • Make sure that the radiator reserve tank assembly still has some coolant in it.

        • If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

        • If there is not enough coolant, the engine may overheat or be seriously damaged.

        • If the radiator reserve tank assembly does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reserve tank assembly is filled to the full line.

    8. Stop the engine and wait until the engine coolant cools down.

    9. Add engine coolant to the full line on the radiator reserve tank assembly.

  14. INSPECT FOR COOLANT LEAK (for Engine)

    Note

    Before performing each inspection, turn the A/C switch off.


    1. A01HU5A

      Fill the radiator with coolant and attach a radiator cap tester.

    2. Put the engine in inspection mode Click here.

    3. Warm up the engine.

    4. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.

      If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  15. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 7 clips.

  16. INSTALL ENGINE UNDER COVER LH

  17. INSTALL ENGINE UNDER COVER RH

  18. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

  19. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH