CYLINDER HEAD REPLACEMENT


  1. REPLACE INTAKE VALVE GUIDE BUSH


    1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    2. Place the cylinder head on wooden blocks.

    3. A01HTZLE04

      Using SST and a hammer, tap out the intake valve guide bush.

      SST
      09201-01055
      09950-70010   ( 09951-07100 )
    4. A01HTUK

      Using a caliper gauge, measure the bush bore diameter of the cylinder head.

      Standard bush bore diameter
      10.285 to 10.306 mm (0.405 to 0.406 in.)

      If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.

    5. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

    6. Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

      Bush Bore Diameter
      Bush Size Specified Condition
      STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
      O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
      Standard bush length
      41.3 to 41.7 mm (1.626 to 1.642 in.)

    7. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    8. A01HUZXE05
      Text in Illustration
      *a Height

      Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
      Standard protrusion height
      14.8 to 15.2 mm (0.582 to 0.598 in.)
    9. A01HT0L

      Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

      Standard oil clearance
      0.025 to 0.060 mm (0.000984 to 0.00236 in.)

  2. REPLACE EXHAUST VALVE GUIDE BUSH


    1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    2. Place the cylinder head on wooden blocks.

    3. A01HSQWE05

      Using SST and a hammer, tap out the exhaust valve guide bush.

      SST
      09201-01055
      09950-70010   ( 09951-07100 )
    4. A01HVSO

      Using a caliper gauge, measure the bush bore diameter of the cylinder head.

      Standard bush bore diameter
      10.285 to 10.306 mm (0.405 to 0.406 in.)

      If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.

    5. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

    6. Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

      Bush Bore Diameter
      Bush Size Specified Condition
      STD 10.333 to 10.344 mm (0.4068 in 0.4072 in.)
      O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
      Standard bush length
      46.8 to 47.2 mm (1.843 to 1.858 in.)

    7. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    8. A01HV7HE05
      Text in Illustration
      *a Height

      Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
      Standard protrusion height
      14.2 to 14.6 mm (0.559 to 0.575 in.)
    9. A01HURU

      Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

      Standard oil clearance
      0.030 to 0.065 mm (0.00118 to 0.00256 in.)

  3. REPLACE RING PIN

    Note

    It is not necessary to remove the ring pin unless it is being replaced.


    1. Remove the ring pins.

    2. A01HUO2E01

      Using a plastic-faced hammer, tap in 2 new ring pins to the cylinder head.

      Standard protrusion height
      6.5 to 7.5 mm (0.256 to 0.295 in.)