HYBRID BATTERY SYSTEM, Diagnostic DTC:P3011-123, P3012-123, P3013-123, P3014-123, P3015-123, P3016-123, P3017-123, P3018-123, P3019-123, P3020-123, P3021-123, P3022-123, P3023-123, P3024-123, P3025-123, P3026-123, P3027-123

DTC Code DTC Name
P3011-123 Battery Block 1 Becomes Weak
P3012-123 Battery Block 2 Becomes Weak
P3013-123 Battery Block 3 Becomes Weak
P3014-123 Battery Block 4 Becomes Weak
P3015-123 Battery Block 5 Becomes Weak
P3016-123 Battery Block 6 Becomes Weak
P3017-123 Battery Block 7 Becomes Weak
P3018-123 Battery Block 8 Becomes Weak
P3019-123 Battery Block 9 Becomes Weak
P3020-123 Battery Block 10 Becomes Weak
P3021-123 Battery Block 11 Becomes Weak
P3022-123 Battery Block 12 Becomes Weak
P3023-123 Battery Block 13 Becomes Weak
P3024-123 Battery Block 14 Becomes Weak
P3025-123 Battery Block 15 Becomes Weak
P3026-123 Battery Block 16 Becomes Weak
P3027-123 Battery Block 17 Becomes Weak

DESCRIPTION


DTC No. INF Code DTC Detection Condition Trouble Area

P3011

P3012

P3013

P3014

P3015

P3016

P3017

P3018

 123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).

  • HV battery

  • Battery smart unit
P3019 123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).

  • HV battery

  • Battery smart unit

  • Service plug grip

P3020

P3021

P3022

P3023

P3024

P3025

P3026

P3027

 123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).

  • HV battery

  • Battery smart unit

Tech Tips

P3011-123 to P3027-123 will not be set unless the vehicle is driven for approximately 10 minutes after clearing the DTCs.

MONITOR DESCRIPTION

If there is an abnormal internal resistance or electromotive voltage in the battery blocks, the battery smart unit determines that a malfunction has occurred. When the malfunction detection condition is satisfied, the power management control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY

Related DTCs P3011 to P3019 and P3020 to P3027 (INF 123): Battery cell malfunction
Required sensors / components HV battery
Frequency of operation Continuous
Duration TMC's intellectual property
MIL operation TMC's intellectual property
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present TMC's intellectual property
Other conditions belong to TMC's intellectual property -

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property -

COMPONENT OPERATING RANGE

Battery smart unit DTC P3011 (INF 123) to P3019 (INF 123) and DTC P3020 (INF 123) to P3027 (INF 123) is not detected

CONFIRMATION DRIVING PATTERN


  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG) and turn the Techstream on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the power switch off.

  5. Turn the power switch on (READY) and turn the Techstream on.

  6. Perform a universal trip.

  7. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  8. Check that permanent DTCs are cleared.

    Tech Tips


    • If a permanent DTC is output, the system is malfunctioning.

    • If no permanent DTC is output, the system is normal.

INSPECTION PROCEDURE

CAUTION:

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read output DTCs Click here.

      Result
      Result Proceed to
      P0AFC-123 is not output. A
      P0AFC-123 is also output. B

    5. Turn the power switch off.

    6. Disconnect the Techstream from the DLC3.


    B

    GO TO DTC CHART (HYBRID BATTERY SYSTEM)

    A

  2. READ VALUE USING TECHSTREAM (VB1 - VB17)


    1. Ensure the safety of the areas in front and at the back of the vehicle.

    2. Apply the parking brake and secure the wheels using chocks.

    3. Connect the Techstream to the DLC3.

    4. Turn the power switch on (READY).

    5. Fully warm up the engine and turn the air conditioning off.

    6. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery block Vol - V01 to V17.

    7. Firmly depress the brake pedal with your left foot.

    8. Move the select lever to D.

    9. Record each battery block voltage from the data list (Battery block Vol -V01 to V17) while fully depressing the accelerator pedal.

    10. Compare the battery block voltages (Battery block Vol -V01 to V17) between the even and odd number groups in each combination shown in the table below.

      Table 1
      Circuit A Battery Block Circuit B Battery Block Condition
      Battery Block Vol-V01 (VB1) Battery Block Vol-V02 (VB2) "Battery Block Vol - V01" - "Battery Block Vol - V02" = 0.3 V or more
      Battery Block Vol-V04 (VB4) Battery Block Vol-V03 (VB3) "Battery Block Vol - V04" - "Battery Block Vol - V03" = 0.3 V or more
      Battery Block Vol-V05 (VB5) Battery Block Vol-V06 (VB6) "Battery Block Vol - V05" - "Battery Block Vol - V06" = 0.3 V or more
      Battery Block Vol-V08 (VB8) Battery Block Vol-V07 (VB7) "Battery Block Vol - V08" - "Battery Block Vol - V07" = 0.3 V or more
      Battery Block Vol-V09 (VB9) Battery Block Vol-V10 (VB10) "Battery Block Vol - V09" - "Battery Block Vol - V10" = 0.3 V or more
      Battery Block Vol-V12 (VB12) Battery Block Vol-V11 (VB11) "Battery Block Vol - V12" - "Battery Block Vol - V11" = 0.3 V or more
      Battery Block Vol-V13 (VB13) Battery Block Vol-V14 (VB14) "Battery Block Vol - V13" - "Battery Block Vol - V14" = 0.3 V or more
      Battery Block Vol-V16 (VB16) Battery Block Vol-V15 (VB15) "Battery Block Vol - V16" - "Battery Block Vol - V15" = 0.3 V or more
      Battery Block Vol-V17 (VB17) Battery Block Vol-V14 (VB14) "Battery Block Vol - V17" - "Battery Block Vol - V14" = 0.3 V or more
      Table 2
      Circuit A Battery Block Circuit B Battery Block Condition
      Battery Block Vol-V01 (VB1) Battery Block Vol-V02 (VB2) "Battery Block Vol - V02" - "Battery Block Vol - V01" = 0.3 V or more
      Battery Block Vol-V04 (VB4) Battery Block Vol-V03 (VB3) "Battery Block Vol - V03" - "Battery Block Vol - V04" = 0.3 V or more
      Battery Block Vol-V05 (VB5) Battery Block Vol-V06 (VB6) "Battery Block Vol - V06" - "Battery Block Vol - V05" = 0.3 V or more
      Battery Block Vol-V08 (VB8) Battery Block Vol-V07 (VB7) "Battery Block Vol - V07" - "Battery Block Vol - V08" = 0.3 V or more
      Battery Block Vol-V09 (VB9) Battery Block Vol-V10 (VB10) "Battery Block Vol - V10" - "Battery Block Vol - V09" = 0.3 V or more
      Battery Block Vol-V12 (VB12) Battery Block Vol-V11 (VB11) "Battery Block Vol - V11" - "Battery Block Vol - V12" = 0.3 V or more
      Battery Block Vol-V13 (VB13) Battery Block Vol-V14 (VB14) "Battery Block Vol - V14" - "Battery Block Vol - V13" = 0.3 V or more
      Battery Block Vol-V16 (VB16) Battery Block Vol-V15 (VB15) "Battery Block Vol - V15" - "Battery Block Vol - V16" = 0.3 V or more
      Battery Block Vol-V17 (VB17) Battery Block Vol-V14 (VB14) "Battery Block Vol - V14" - "Battery Block Vol - V17" = 0.3 V or more

      Tech Tips

      Make sure to compare Battery Block Vol-V17 to Battery Block Vol-V14 in accordance with the table above.

      A01HSN4E14

      Tech Tips

      When an internal malfunction occurs in the battery smart unit, this symptom (difference in voltage of 0.3 V or more for all 9 pairs of blocks) will occur.

      Result
      Result Proceed to
      All conditions in table 1 are met. A
      All conditions in table 2 are met.
      Other than above. B

    11. Turn the power switch off.

    12. Disconnect the Techstream from the DLC3.


    B

    CHECK DTC OUTPUT (HYBRID CONTROL) Click here

    A

    REPLACE BATTERY SMART UNIT Click here

  3. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      P3019-123 is output. A
      P3019-123 is not output. B

      Tech Tips

      DTC P3019-123 may also stored if there is foreign matter, etc. adhering to the connecting part of the service grip.

    5. Turn the power switch off.


    B

    REPLACE HV BATTERY Click here

    A

    REPLACE SERVICE PLUG GRIP AND HV BATTERY Click here