BLACK OUT TAPE (for Rear Door) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01ELAN

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.

  3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A01EIUY

      Using a moulding remover, disengage the 2 clips and 5 claws.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01EKV3

      Remove the 2 screws.

    2. Using a clip remover, disengage the 8 clips.

    3. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    4. Raise the rear door trim board sub-assembly and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    5. A01EKW8

      Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

    6. for 13 Speakers:


      1. Disconnect the connector.

  5. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01EL35

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door inside handle sub-assembly.

  6. REMOVE REAR DOOR FRAME GARNISH


    1. A01EIMS

      Disengage the clip and remove the rear door frame garnish.

      Tech Tips

      This garnish needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.

  7. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01EJGM

      Disconnect the 2 connectors.

    2. disengage the 2 clamps and remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  8. REMOVE REAR DOOR CHECK ASSEMBLY


    1. A01EJQM

      Remove the bolt, 2 nuts and rear door check assembly.

  9. REMOVE REAR DOOR WEATHERSTRIP


    1. A01EJ4C

      Using a clip remover, disengage the 21 clips and remove the front door weatherstrip.

  10. REMOVE REAR DOOR GLASS RUN


    1. A01EJ8N

      Remove the rear door glass run.

  11. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A01EKAX

      Remove the hole plug.

    2. A01EL0LE01

      Remove the 2 screws.

    3. Loosen the temporary bolt.

      Text in Illustration
      *1 Temporary Bolt

    4. Remove the bolt and rear door window division bar sub-assembly.

    5. Remove the temporary bolt from the rear door window division bar sub-assembly.

  12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01EK54

      Remove the hole plug.

    2. Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

    3. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the power window regulator switch assembly and the rear power window regulator motor connector.

    5. Disconnect the cable from the negative (-) battery terminal.

    6. A01EJMB

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    7. A01EJRVE01

      Remove the rear door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  13. REMOVE REAR DOOR OUTSIDE STRIPE


    1. Using a heat light, heat the rear door outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01EKMB

      Pull back on one of the ends of the rear door outside stripe to remove it.

      Tech Tips

      When pulling on the tape, pull it parallel to the body.

  14. REMOVE REAR DOOR LOWER OUTSIDE STRIPE


    1. Using a heat light, heat the rear door lower outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01ELXN

      Pull back on one of the ends of the rear door lower outside stripe to remove it.

      Tech Tips

      When pulling on the tape, pull it parallel to the body.

  15. REMOVE NO. 2 BLACK OUT TAPE


    1. Using a heat light, heat the No. 2 black out tape and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01EMFB

      Pull back on one of the ends of the No. 2 black out tape to remove it.

      Tech Tips

      When pulling on the tape, pull it parallel to the body.