REAR COMBINATION LIGHT ASSEMBLY REMOVAL


  1. REMOVE REAR DOOR SCUFF PLATE


    1. A01EMQ6

      Disengage the 2 clips and 6 claws, and remove the rear door scuff plate LH.

  2. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    1. A01EMNU

      Remove the rear part of the rear door opening trim weatherstrip to the extent that allows removal of the deck trim side panel assembly and roof side inner garnish assembly.

  3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  4. REMOVE DECK BOARD ASSEMBLY


    1. A01EL2J

      Disengage the 2 guides and remove the deck board assembly.

  5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A01EINV

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  6. REMOVE DECK SIDE TRIM BOX LH


    1. A01ELW2

      Remove the 3 clips and remove the deck side trim box LH.

  7. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A01EMLZ

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  8. REMOVE DECK SIDE TRIM BOX RH


    1. A01EIQE

      Remove the 4 clips and remove the deck side trim box RH.

  9. REMOVE NO. 1 DECK BOARD


    1. A01EK32

      Disengage the 6 clips and remove the No. 1 deck board.

  10. REMOVE REAR SEAT SUB FLOOR PANEL ASSEMBLY


    1. A01ELM5

      Disengage the 2 claws, 2 guides and 5 clips, and remove the rear seat sub floor panel assembly.

  11. REMOVE REAR FLOOR FINISH PLATE


    1. A01EJJN

      Disengage the 2 claws and 4 clips, and remove the rear floor finish plate.

  12. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

  13. REMOVE REAR SEAT INNER TRACK BRACKET COVER (for LH Side)


    1. A01ELIO

      Disengage the 3 claws and guide, and remove the rear seat inner track bracket cover as shown in the illustration.

  14. REMOVE REAR SEAT OUTER TRACK BRACKET COVER (for LH Side)


    1. A01EJ71

      Disengage the 3 claws and guide, and remove the rear seat outer track bracket cover as shown in the illustration.

  15. DISCONNECT REAR SEAT NO. 2 RECLINING CONTROL CABLE SUB-ASSEMBLY (for LH Side)


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A01EJREE01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece
    2. A01EK1VE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A01EMQ8E01
      Text in Illustration
      *1 Seat Track Adjusting Handle *2 Protective Tap

    4. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable sub-assembly as shown in the illustration.

      A01ELW1E01
      Text in Illustration
      *1 Protective Tape - -

    5. Secure the rear seat No. 2 reclining control cable sub-assembly with the carpet hole as shown in the illustration.

  16. REMOVE REAR SEAT ASSEMBLY LH (for LH Side)


    1. A01ELFU

      Remove the 2 bolts on the rear side of the seat.

    2. A01EM4L

      Remove the 2 bolts on the front side of the seat.

    3. Remove the rear seat assembly LH.

      Note

      Be careful not to damage the vehicle body.

  17. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

  18. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY (for RH Side)

  19. REMOVE REAR SEAT INNER TRACK BRACKET COVER (for RH Side)


    1. A01EM8W

      Disengage the 3 claws and guide, and remove the rear seat inner track bracket cover as shown in the illustration.

  20. REMOVE REAR SEAT OUTER TRACK BRACKET COVER (for RH Side)


    1. A01EKLF

      Disengage the 3 claws and guide, and remove the rear seat outer track bracket cover as shown in the illustration.

  21. DISCONNECT REAR SEAT RECLINING CONTROL CABLE SUB-ASSEMBLY (for RH Side)


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A01EJOCE01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece
    2. A01EKXEE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A01EK6GE01
      Text in Illustration
      *1 Protective Tape *2 Seat Track Adjusting Handle

    4. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable sub-assembly as shown in the illustration.

      A01ELATE01
      Text in Illustration
      *1 Protective Tape - -

  22. REMOVE REAR SEAT ASSEMBLY RH (for RH Side)


    1. A01EMPM

      Remove the 3 bolts on the rear side of the seat.

    2. A01EMC9

      Remove the 2 bolts on the front side of the rear seat assembly RH.

    3. Remove the rear seat assembly RH.

      Note

      Be careful not to damage the vehicle body.

  23. REMOVE RECLINING REMOTE CONTROL BEZEL


    1. A01EIRXE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 3 claws and remove the reclining remote control bezel LH.

      Tech Tips

      Tape the screwdriver tip before use.

  24. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


    1. A01EJ2H

      Remove the 2 bolts.

    2. Disengage the 2 guides and remove the 2 luggage hold belt striker assemblies.

  25. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY


    1. A01EIYD

      Remove the bolt and disconnect the floor end of the rear seat outer belt assembly.

  26. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)


    1. Remove the bolt and clip.

    2. Disengage the 7 claws and 5 clips.

    3. Disconnect the connector and remove the deck trim side panel assembly LH.

      A01EJPS

  27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)


    1. Remove the bolt and clip.

    2. Disengage the 7 claws and 6 clips.

    3. Disconnect each connector and remove the deck trim side panel assembly RH.

      A01EM0U

  28. REMOVE REAR BUMPER ASSEMBLY

    Click here

  29. REMOVE REAR COMBINATION LIGHT ASSEMBLY


    1. A01EJSA

      Remove the 2 nuts.

    2. Disconnect the connector.

    3. Disengage the clamp.

    4. A01EJ6YE01
      Text in Illustration
      *1 Pin
      *2 Guide

      Disengage the 2 pins and guide, and remove the rear combination light assembly as shown in the illustration.