LIGHTING SYSTEM SYSTEM DESCRIPTION


  1. AUTOMATIC LIGHT CONTROL SYSTEM

    When the light control switch is in the AUTO position, the automatic light control system detects ambient light levels and controls the low beam headlights, parking lights, taillights, marker lights and license plate lights.

  2. LIGHT AUTO TURN-OFF SYSTEM

    The light auto turn-off system is used to prevent the exterior lights from being accidentally left on (low beam headlights, high beam headlights, front fog lights, taillights, parking lights, license plate lights and marker lights).


    • This system has the following functions.

    Function Outline
    Driver Side Door-linked Function

    The exterior lights automatically turn off when all of the following conditions have been met:


    • The ignition switch is turned from ON to off.

    • The light control switch is in the tail position.

    • The driver side door is opened.
    Delay Function

    The exterior lights automatically turn off after 30 seconds when all of the following conditions have been met:


    • The ignition switch is turned from ON to off.

    • The low beam headlights are on (light control switch is in the head or AUTO position).

    • All doors are closed after any of the doors are opened.
    Door Control Transmitter-linked Function

    The exterior lights turn off immediately when the delay function is active and the following condition has been met:


    • The lock button on the key is pushed after all doors are locked.

  3. DAYTIME RUNNING LIGHT SYSTEM

    The daytime running light system is designed to automatically illuminate the daytime running lights during the daytime to make the vehicle more visible to other vehicles.


    • This system is controlled by the main body ECU (driver side junction block assembly) and power distributor (engine room junction block assembly). The main body ECU (driver side junction block assembly) transmits a turn on signal to the power distributor (engine room junction block assembly), which illuminates the high-intensity parking lights.

    • This system is enabled when the following conditions are met:


      • Ignition switch is ON.

      • Engine speed signal is input (engine running).

      • Parking brake switch is off.

      • Light control switch is in the off, tail or AUTO position (and the low beam headlights are not turned on via the automatic light control system).

  4. AUTOMATIC HIGH BEAM SYSTEM


    1. General

      The automatic high beam system enhances the illumination of the area to the front of the vehicle to improve visibility for the driver. It works by detecting light from the front using the camera built into the inner rear view mirror assembly and turning the high beams of the headlights on or off automatically.

    2. Function of Main Components

      Component Outline
      Automatic High Beam Sensor (Inner Rear View Mirror Assembly) Determines when to turn the high beams on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its camera sensor. Then, it sends high beam request signals to the AFS ECU (headlight swivel ECU assembly) via LIN.
      AFS ECU (Headlight Swivel ECU Assembly)

      Acts as the gateway between the automatic high beam sensor (inner rear view mirror assembly) which uses LIN communication and the CAN No. 2 bus. In addition, it stores Diagnostic Trouble Codes (DTCs) if an automatic high beam sensor (inner rear view mirror assembly) malfunction occurs.

      Tech Tips

      Even though the vehicle is not equipped with AFS, an AFS ECU (headlight swivel ECU assembly) is provided.
      Power Management Control ECU Assembly Performs the gateway function between the No. 1 bus and No. 2 bus.
      Steering Angle Sensor Outputs the steering angle information to the AFS ECU (headlight swivel ECU assembly).
      Skid Control ECU Outputs the information about the speed of the right front wheel . This information is used by the automatic high beam sensor (inner rear view mirror assembly) to turn the high beams on and off.
      ECM Outputs a signal to indicate that the shift lever is in R. Based on this signal, the automatic high beam sensor (inner rear view mirror assembly) turns the high beams off.
      Combination Meter Assembly

      Displays automatic high beam indicator light when it receives illuminate or blink request signals from the main body ECU (driver side junction block assembly).

      Tech Tips


      • The automatic high beam indicator light flashes to inform the driver when the malfunction is in this system.

      • The automatic high beam indicator light illuminates to inform the driver when the automatic high beam system is activated.

      • The automatic high beam indicator light will turn off when there is bad weather (deep fog, heavy rain, etc.), an abnormal condition with front windshield (snow, ice, etc.), or an obstruction to the camera field of view (parking tag, etc.).
      Main Body ECU (Driver Side Junction Block Assembly)

      • Receives the light control switch AUTO position and dimmer switch high position signals from the headlight dimmer switch assembly, and receives the automatic light control sensor signal to determine the low beam headlight illumination condition, and sends this information to the AFS ECU (headlight swivel ECU assembly). These are used to put the automatic high beam system in standby mode.


      • Receives high beam drive request signals from the AFS ECU (headlight swivel ECU assembly), and outputs the a duty control value to the power distributor (engine room junction block assembly).


      • Performs illumination control for the automatic high beam system and stores Diagnostic Trouble Codes (DTCs) when the system malfunctions.
      Power Distributor (Engine Room Junction Block Assembly) Performs duty control for the high beam bulbs based on drive request signals that are received from the main body ECU (driver side junction block assembly).

    3. Basic Function


      1. When all of the following conditions are met, the automatic high beam system is activated and the automatic high beam indicator light turns on:


        • The ignition switch is ON.

        • The light control switch is in the AUTO position and the low beam headlights are on.

        • The dimmer switch is in the high position.

      2. When the following conditions are met, the high beams automatically turn on after a short delay:


        • Vehicle speed is more than approximately 20 mph (32 km/h).

        • The area in front of the vehicle is dark.

        • There are no oncoming vehicles with headlights on.

        • There are no preceding vehicles with taillights on.

        • There are few streetlights along the street ahead.

      3. When any of the following conditions are met, the high beams automatically turn off after a short delay:


        • Vehicle speed is less than 20 mph (32 km/h).

        • The level of ambient light is higher than a specified threshold.

        • There are oncoming vehicles with headlights on.

        • There are preceding vehicles with taillights on.

        • There are several streetlights along the street ahead.

      4. When any of the following conditions are met, the automatic high beam system will be canceled and the indicator light will turn off.


        • The ignition switch is turned off.

        • The light control switch is turned to any position except the AUTO position.

        • The light control switch is in the AUTO position, however the low beams are not on.

        • The dimmer switch is moved to the low position.

        Tech Tips

        It is possible to manually switch between the high beams and low beams using either of the following operations:


        • Turn the light control switch from the AUTO position to the head position. In this case, the high beams turn on according to the dimmer switch high position. To change to the low beams, move the dimmer switch to the low position.


        • Move the dimmer switch from the high position to the low position. In this case, the low beams turn on according to the dimmer switch position.

        Tech Tips

        The automatic high beam system monitors the area in front of the vehicle using the camera built into the inner rear view mirror assembly and makes a judgment to turn on the high beams when the surrounding area is dark (there are no headlights from oncoming vehicles and no taillights from vehicles in front). High beam control limitations:


        • When the surrounding area is not dark enough, the low beams will remain on even if the headlights are turned on by the automatic light control system and the automatic high beam indicator light on the combination meter assembly illuminates. (The light level sufficient to turn the auto low beams on is not the same as the light level required to automatically illuminate the high beams.)


        • When an oncoming vehicle suddenly appears at a sharp curve or a vehicle crosses the path of the vehicle, the high beams may remain on.


        • When the fog lights of an oncoming vehicle are detected, the high beams may be turned off.


        • The timing of the high beams turning on and off may differ depending on the brightness of headlights or fog lights from oncoming vehicles or the taillights of preceding vehicles.


        • The timing of the high beams turning on and off may differ between normal conditions (good weather) and when driving on wet, frozen or snowy roads.

        • The timing of the high beams turning on and off may differ depending on the number of occupants and amount of cargo present.


        • On some occasions, the high beams and low beams may change unexpectedly.

        Tech Tips

        The camera built into the inner rear view mirror assembly continually monitors the light level in the area to the front of the vehicle. There is a delay in turning on the high beams. Even when there is no ambient light, the high beams will not turn on immediately. The delay will vary depend on the situation.

  5. BI-FUNCTION


    1. The headlights have a bi-function. This bi-function increases the upper illumination area of the discharge bulb (low/high beam) when the high beam is turned on.


      • If the low beam is selected, the upper illumination area of the discharge bulb is blocked by a shade and only the lower illumination area is used. If the high beam is selected, the headlight solenoid slides the shutter (shade) down to allow use of the upper illumination area, thus increasing the illumination area and improving visibility when the high beam is on.

      • This function is activated by the front controller. The front controller receives a high beam turn on signal from the main body ECU and activates the headlight solenoid built into the headlight unit to slide the shade down.

      A01EJVLE01

  6. HID HEADLIGHT SYSTEM

    The High Intensity Discharge (HID) headlight system uses a discharge bulb as its light source for the low beam. Discharge bulbs are superior to halogen bulbs.


    • Discharge bulbs have the following features:


      • The light emitted by the bulb is close in color to sunlight. The light shines further forward and over a broader area, increasing the area visible to the driver.

      • Less power is consumed.

    • This system consists of the discharge bulbs and light control ECUs.

    • The light control ECU transforms voltage that is input from the battery to high voltage of up to 30000 V and applies it to the discharge bulbs in order to illuminate them.

  7. AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM


    1. General


      • This system maintains the low beam headlights at a constant level while the vehicle is stopping.

      • This system is controlled by the headlight leveling ECU assembly. The headlight leveling ECU assembly detects the vehicle posture via the rear height control sensor sub-assembly RH, and detects the vehicle speed via the combination meter assembly. The headlight leveling ECU assembly controls each headlight leveling motor (headlight unit) based on these pieces of information in order to change the headlight reflector angle.

      Note


      • Initialize the rear height control sensor sub-assembly RH signal after the vehicle height changes due to replacement of the suspension or after such operations as reinstallation or replacement of the rear height control sensor sub-assembly RH.

      • When the headlight leveling ECU assembly is replaced, initialization is also necessary.

    2. Function of Main Components

      Component Outline
      Rear Height Control Sensor Sub-assembly RH Detects vehicle height.
      Combination Meter Assembly

      • Outputs the vehicle speed signal to the headlight leveling ECU assembly.

      • The headlight beam level control system indicator light in the combination meter illuminates for 3 seconds and then goes off when the ignition switch is turned to ON (bulb check function).

      • The headlight beam level control system indicator light in the combination meter illuminates to alert the driver when a malfunction in this system is detected.
      Headlight Leveling Motor (Headlight Unit) Based on the signals received from the headlight leveling ECU assembly, each motor moves the reflector in the headlight to vary its low beam.
      Headlight Leveling ECU Assembly

      • Based on the signals that are transmitted by the rear height control sensor sub-assembly RH and combination meter assembly, the headlight leveling ECU assembly detects the amount of variance of the vehicle posture while the vehicle is stopping.

      • Based on the detected value, the headlight leveling ECU assembly outputs control signals to the headlight leveling motor (headlight unit).

      • The headlight leveling ECU assembly turns on the headlight beam level control system indicator light for 3 seconds when the ignition switch is turned to ON (bulb check function).

      • The headlight leveling ECU assembly turns on the headlight beam level control system indicator light to alert the driver when a malfunction in this system is detected.

  8. DOOR MIRROR FOOT LIGHT SYSTEM


    1. General


      • The door mirror foot light control consists primarily of the fade-in/fade-out function and timer illumination function.

      • This control is controlled by the main body ECU (driver side junction block assembly).

    2. The door mirror foot light system has the following control functions:

      Function Outline
      Actuation Area-linked*1

      When all of the following conditions are met, the lights that operate turn on:


      • The ignition switch is off.

      • All doors are closed.

      • A key is detected in the actuation area.

      When the following condition is met, the lights that operate turn off:


      • A key is not detected in the actuation area.
      Door Unlock-linked

      When all of the following conditions are met, the lights that operate turn on:


      • The ignition switch is off.

      • All doors are closed.

      • Any door is unlocked when all doors are locked.
      Door Lock-linked

      When either of the following conditions is met, the lights that operate turn off:


      • All doors are locked when all doors are closed and any door is unlocked.

      • All doors are locked again when all doors are closed and locked.
      Delay

      When approximately 15 seconds elapse after either of the following conditions is met, the lights that operate turn off:


      • An actuation area-linked function is used.

      • A door unlock-linked function is used.

      When either of the following conditions is met while the delay function is operating, the lights that operate remain on for approximately 15 seconds longer:


      • Any door is opened.

      • Any door is closed.
      Shift Lever Position-linked

      When both of the following conditions are met, the lights that operate turn off:


      • The ignition switch is ON.

      • The shift lever is in any position other than P.

      • *1: w/ Smart Entry and Start System