FUEL LID LOCK CONTROL CABLE ASSEMBLY INSTALLATION


  1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    1. Engage the 8 clamps.

      A01EKXB
    2. A01EK92

      Engage the 2 claws and connect the fuel lid lock control cable sub-assembly.

  2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01ELP8

      Connect the fuel lid lock control cable sub-assembly.

    2. A01ELRU

      Install the fuel lid lock open lever sub-assembly with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Engage the 7 claws and the 5 clips.

    3. Install the deck trim side panel assembly LH with the bolt and clip.

      A01EJPS

  4. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A01EKS4E01
      Text in Illustration
      *1 Protruding Part

      Connect the floor anchor end of the rear seat outer belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding part of the floor panel.

  5. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY LH


    1. A01EJ2H

      Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  6. INSTALL RECLINING REMOTE CONTROL BEZEL LH


    1. A01EKL1

      Engage the 3 claws to install the reclining remote control bezel LH.

  7. INSTALL REAR SEAT ASSEMBLY LH


    1. Place the rear seat assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A01EM4L

      Temporarily install the 2 bolts on the front side of the seat.

    3. A01ELFU

      Temporarily install the 2 bolts on the rear side of the seat.

    4. Install the rear seat assembly LH with the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  8. CONNECT REAR SEAT NO. 2 RECLINING CONTROL CABLE SUB-ASSEMBLY


    1. Remove the rear seat No. 2 reclining control cable from the carpet hole.

      A01EKQ0

    2. Connect the rear seat No. 2 reclining control cable sub-assembly as shown in the illustration.

      A01EM4DE01
      Text in Illustration
      *1 Protective Tape *2 Seat Track Adjusting Handle
    3. A01EMK9

      Engage the 2 claws and connect the rear seat No. 2 reclining control cable sub-assembly as shown in the illustration.

    4. Return the seatback to the upright position.

    5. Pull up the adjuster's lock piece to lock it as shown in the illustration.

      A01EL0OE01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece

      Note

      When pressing the lock piece, make sure the adjuster's spring is not compressed.

  9. INSTALL REAR SEAT OUTER TRACK BRACKET COVER LH


    1. A01EJVG

      Engage the guide and 3 claws and install the rear seat outer track bracket cover as shown in the illustration.

  10. INSTALL REAR SEAT INNER TRACK BRACKET COVER LH


    1. A01EIZH

      Engage the guide and 3 claws and install the rear seat inner track bracket cover as shown in the illustration.

  11. INSTALL REAR SEAT HEADREST ASSEMBLY LH

  12. INSTALL REAR FLOOR FINISH PLATE


    1. A01EJJN

      Engage the 4 clips and 2 claws to install the rear floor finish plate.

  13. INSTALL REAR SEAT SUB FLOOR PANEL ASSEMBLY


    1. A01ELM5

      Engage the 2 guides, 2 claws and 5 clips to install the rear seat sub floor panel assembly.

  14. INSTALL NO. 1 DECK BOARD


    1. A01EK32

      Engage the 6 clips to install the No. 1 deck board.

  15. INSTALL DECK SIDE TRIM BOX LH


    1. A01ELW2

      Install the deck side trim box LH with the 3 clips.

  16. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A01EINV

      Engage the 2 guides to install the No. 3 deck board sub-assembly.

  17. INSTALL DECK SIDE TRIM BOX RH


    1. A01EIQE

      Install the deck side trim box RH with the 4 clips.

  18. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A01EMLZ

      Engage the 2 guides to install the No. 2 deck board sub-assembly.

  19. INSTALL DECK BOARD ASSEMBLY


    1. A01EL2J

      Engage the 2 guides to install the deck board assembly.

  20. INSTALL TONNEAU COVER ASSEMBLY


    1. Install the tonneau cover assembly.

  21. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. A01EL6Q

      Engage the guide, 2 claws and the 2 clips to install the lower center pillar garnish LH as shown in the illustration.

  22. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01EL5J

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  23. INSTALL LAP BELT OUTER ANCHOR COVER LH


    1. A01EJOK

      Engage the 3 claws to install the lap belt outer anchor cover.

  24. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EL3EE02
      Text in Illustration
      *1 Alignment mark (Purple)

      Align the alignment mark (Purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  25. INSTALL REAR DOOR SCUFF PLATE LH


    1. A01EMQ6

      Engage the 2 clips and 6 claws to install the rear door scuff plate LH.

  26. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EJYAE01
      Text in Illustration
      *1 Alignment mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  27. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01EJEA

      Engage the 2 clips to install the cowl side trim sub-assembly LH.

    2. Install the clip.

  28. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A01ELE9

      Engage the guide, 3 clips and the 7 claws to install the front door scuff plate LH.

  29. INSTALL FRONT SEAT ASSEMBLY LH

    Click here