POWER BACK DOOR DRIVE UNIT REMOVAL


  1. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01EMQ6

      Disengage the 2 clips and 6 claws, and remove the rear door scuff plate LH.

  2. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EJBD

      Remove the rear door opening trim weatherstrip LH.

  3. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  4. REMOVE DECK BOARD ASSEMBLY


    1. A01EL2J

      Disengage the 2 guides and remove the deck board assembly.

  5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A01EINV

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  6. REMOVE DECK SIDE TRIM BOX LH


    1. A01ELW2

      Remove the 3 clips and remove the deck side trim box LH.

  7. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A01EMLZ

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  8. REMOVE DECK SIDE TRIM BOX RH


    1. A01EIQE

      Remove the 4 clips and remove the deck side trim box RH.

  9. REMOVE NO. 1 DECK BOARD


    1. A01EK32

      Disengage the 6 clips and remove the No. 1 deck board.

  10. REMOVE REAR SEAT SUB FLOOR PANEL ASSEMBLY


    1. A01ELM5

      Disengage the 2 claws, 2 guides and 5 clips, and remove the rear seat sub floor panel assembly.

  11. REMOVE REAR FLOOR FINISH PLATE


    1. A01EJJN

      Disengage the 2 claws and 4 clips, and remove the rear floor finish plate.

  12. REMOVE REAR SEAT HEADREST ASSEMBLY LH

  13. REMOVE REAR SEAT INNER TRACK BRACKET COVER LH


    1. A01ELIO

      Disengage the 3 claws and guide, and remove the rear seat inner track bracket cover as shown in the illustration.

  14. REMOVE REAR SEAT OUTER TRACK BRACKET COVER LH


    1. A01EJ71

      Disengage the 3 claws and guide, and remove the rear seat outer track bracket cover as shown in the illustration.

  15. DISCONNECT REAR SEAT NO. 2 RECLINING CONTROL CABLE SUB-ASSEMBLY


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A01EJREE01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece
    2. A01EK1VE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A01EMQ8E01
      Text in Illustration
      *1 Seat Track Adjusting Handle *2 Protective Tap

    4. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable sub-assembly as shown in the illustration.

      A01ELW1E01
      Text in Illustration
      *1 Protective Tape - -

    5. Secure the rear seat No. 2 reclining control cable sub-assembly with the carpet hole as shown in the illustration.

  16. REMOVE REAR SEAT ASSEMBLY LH


    1. A01ELFU

      Remove the 2 bolts on the rear side of the seat.

    2. A01EM4L

      Remove the 2 bolts on the front side of the seat.

    3. Remove the rear seat assembly LH.

      Note

      Be careful not to damage the vehicle body.

  17. REMOVE RECLINING REMOTE CONTROL BEZEL LH


    1. A01EIRXE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 3 claws and remove the reclining remote control bezel LH.

      Tech Tips

      Tape the screwdriver tip before use.

  18. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY LH


    1. A01EJ2H

      Remove the 2 bolts.

    2. Disengage the 2 guides and remove the 2 luggage hold belt striker assemblies.

  19. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A01EIYD

      Remove the bolt and disconnect the floor end of the rear seat outer belt assembly.

  20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the bolt and clip.

    2. Disengage the 7 claws and 5 clips.

    3. Disconnect the connector and remove the deck trim side panel assembly LH.

      A01EJPS

  21. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. w/ Rear Speaker:


      1. Disconnect the connector.

    2. A01ELU9E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the 3 stud bolts.

    3. Remove the bolt and disengage the 10 clips.

    4. Lift the lower edge of the roof side inner garnish assembly LH up and pull it out over the 3 stud bolts while ensuring ample clearance.

      Note

      Do not damage the roof headlining assembly or roof side inner garnish assembly.

    5. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish assembly LH and remove the roof side inner garnish assembly LH.

      A01EJ0LE01
      Text in Illustration
      *1 Stud Bolt - -

  22. REMOVE POWER BACK DOOR ROD


    1. A01EKDCE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the stop ring along the groove.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Release the ball joint and disengage the power back door rod.

    3. A01EJI1E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the stop ring along the groove.

      Tech Tips

      Tape the screwdriver tip before use.

    4. Release the ball joint and remove the power back door rod.

  23. REMOVE POWER BACK DOOR UNIT ASSEMBLY


    1. A01EKGX

      Disconnect the connector.

    2. Remove the 4 bolts and power back door unit assembly.