REAR DOOR ADJUSTMENT

A01EKQKE01

CAUTION:

Before adjusting the door positions of vehicles equipped with side and curtain shield airbags, be sure to disconnect the battery. After adjustment, check that the SRS warning light is operating normally and there are no SRS DTCs output.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

  • Specified torque for standard bolts is shown in the standard bolt chart Click here.


  1. INSPECT REAR DOOR


    1. Check that the clearance measurements of areas *1 through *19 are within each standard range.

      A01EL0EE01
      Standard Clearance
      Area Measurement Area Measurement
      *1 2.5 to 6.5 mm (0.0984 to 0.256 in.) *11 3.0 to 6.0 mm (0.118 to 0.236 in.)
      *2 -2.0 to 2.0 mm (-0.0787 to 0.0787 in.) *12 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      *3 3.5 to 6.5 mm (0.138 to 0.256 in.) *13 3.2 to 7.2 mm (0.126 to 0.283 in.)
      *4 0.5 to 3.5 mm (0.0197 to 0.138 in.) *14 -2.0 to 2.0 mm (-0.0787 to 0.0787 in.)
      *5 3.5 to 6.5 mm (0.138 to 0.256 in.) *15 9.3 to 13.3 mm (0.366 to 0.524 in.)
      *6 0.4 to 3.4 mm (0.0156 to 0.134 in.) *16 3.2 to 7.2 mm (0.126 to 0.283 in.)
      *7 3.5 to 6.5 mm (0.138 to 0.256 in.) *17 -2.0 to 2.0 mm (-0.0787 to 0.0787 in.)
      *8 1.4 to 4.4 mm (0.0551 to 0.173 in.) *18 3.0 to 6.0 mm (0.118 to 0.236 in.)
      *9 3.0 to 6.0 mm (0.118 to 0.236 in.) *19 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      *10 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. ADJUST REAR DOOR


    1. A01EMIP

      Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

      SST
      09812-00010

    2. Tighten the hinge bolts on the vehicle body after the adjustment.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

    3. Loosen the hinge bolts on the door and adjust the door position.

    4. Tighten the hinge bolts on the door after the adjustment.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }
    5. A01EK84

      Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

    6. Using a brass bar and a hammer, hit the striker to adjust its position.

    7. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

  4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. INSPECT SRS WARNING LIGHT

    Click here