OUTER REAR VIEW MIRROR INSTALLATION


  1. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


    1. A01EJXN

      Engage the 3 claws to install the outer rear view mirror assembly as shown in the illustration.

    2. Install the 3 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Connect the connector.

    4. Install the hole plug.

  2. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. A01EJ06E01
      Text in Illustration
      *1 Reference Point

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    3. Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. Engage the clamp.

    5. Install the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY


    1. Install the outer mirror control ECU assembly with the 2 screws.

    2. Connect the 2 connectors.

  4. INSTALL DOOR SIDE AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01EJ32

      Insert the pin (stopper) into the door hole and install the door side airbag sensor to the vehicle with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Make sure that the pin (stopper) is securely inserted into the door hole.

      • Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    4. Connect the connector to the door side airbag sensor.

      Note

      When connecting the airbag connector, take care not to damage the airbag wire harness.


      1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

        A01EMFAE01

      2. Be sure to engage the connectors until they are locked (When locking, make sure that a click sound can be heard).

        A01EKSTE09

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

    5. Check that there is no looseness in the installation parts of the door side airbag sensor.

  5. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01EJRF

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.

    2. A01EKW8

      Engage the 2 claws and install the front door inside handle sub-assembly to the rear door trim board sub-assembly.

  6. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01EJLK

      Engage the 10 clips and install the front door trim board sub-assembly.

    2. Install the 2 screws.

  7. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01EK5PE01

      Engage the claw to install the courtesy light assembly.

  8. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01EL08

      Connect the connector.

    2. Engage the 2 clips and 4 claws, and install the power window regulator master switch assembly with front door armrest base panel.

  9. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01EM97

      Connect the connector.

    2. Engage the 2 clips and 4 claws, and install the power window regulator switch assembly with front door armrest base panel.

  10. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01ELD2

      Engage the 3 claws and install the front door inside handle bezel plug.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSPECT SRS WARNING LIGHT

    Click here