SLIDING ROOF SYSTEM Sliding Roof does not Move by Operating Sliding Roof Control Switch

DESCRIPTION

The sliding roof ECU (sliding roof drive gear sub-assembly) receives switch slide and tilt signals and drives its built-in motor.

WIRING DIAGRAM

A01EMH1E04

INSPECTION PROCEDURE

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • When the sliding roof ECU (sliding roof drive gear sub-assembly) is reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized Click here.

  • Since the sliding roof system uses LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the How to Proceed with Troubleshooting procedure Click here. Then, conduct the following inspection procedure.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS (SLIDING ROOF OPERATION)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Sliding Roof
      Tester Display Test Part Control Range Diagnostic Note
      Slide Roof Operate sliding roof CLOS/UP / OFF -
      Slide Roof Operate sliding roof OPN/DWN / OFF -
      OK
      Sliding roof operates normally.

    NG

    CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY, BODY GROUND) Click here

    OK

  2. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Data List.

    5. Read the Data List according to the display on the GTS.

      Sliding Roof
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Open SW SLIDE OPEN switch signal/ON or OFF

      ON: SLIDE OPEN switch pressed

      OFF: SLIDE OPEN switch not pressed

      		 -
      Close SW SLIDE CLOSE switch signal/ON or OFF

      ON: SLIDE CLOSE switch pressed

      OFF: SLIDE CLOSE switch not pressed

      		 -
      Up SW TILT UP switch signal/ON or OFF

      ON: TILT UP switch pressed

      OFF: TILT UP switch not pressed

      		 -
      Down SW TILT DOWN switch signal/ON or OFF

      ON: TILT DOWN switch pressed

      OFF: TILT DOWN switch not pressed

      		 -
      OK
      The GTS display changes according to switch operation as shown in the table.

    NG

    CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH ASSEMBLY) Click here

    OK

    REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here

  3. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY, BODY GROUND)


    1. A01EKPJE04
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))

      Disconnect the P4 ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      P4-1 (B) - Body ground Always 11 to 14 V
      P4-5 (IG) - Body ground Ignition switch ON 11 to 14 V
      P4-5 (IG) - Body ground Ignition switch off Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-2 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here

  4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH ASSEMBLY)


    1. A01EKIIE04
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))
      *2

      Front view of wire harness connector

      (to Sliding Roof Switch (Roof Console Box Assembly))

      Disconnect the P6 switch connector.

    2. Disconnect the P4 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-9 (CLS) - P6-2 (CLS) Always Below 1 Ω
      P4-9 (CLS) - Body ground Always 10 kΩ or higher
      P4-7 (OPN) - P6-3 (OPN) Always Below 1 Ω
      P4-7 (OPN) - Body ground Always 10 kΩ or higher
      P4-8 (DWN) - P6-4 (DOWN) Always Below 1 Ω
      P4-8 (DWN) - Body ground Always 10 kΩ or higher
      P4-10 (UP) - P6-5 (UP) Always Below 1 Ω
      P4-10 (UP) - Body ground Always 10 kΩ or higher
      P6-1 (GND) - Body ground Always Below 1 Ω
      P4-2 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)


    1. A01EMI5E01
      Text in Illustration
      *1

      Component without harness connected

      Sliding Roof Switch (Roof Console Box Assembly)

      Remove the sliding roof switch (roof console box assembly) Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P6-4 (DOWN) - P6-1 (GND) TILT DOWN switch is pressed Below 1 Ω
      P6-4 (DOWN) - P6-1 (GND) TILT DOWN switch is not pressed 10 kΩ or higher
      P6-5 (UP) - P6-1 (GND) TILT UP switch is pressed Below 1 Ω
      P6-5 (UP) - P6-1 (GND) TILT UP switch is not pressed 10 kΩ or higher
      P6-2 (CLS) - P6-1 (GND) SLIDE CLOSE switch is pressed Below 1 Ω
      P6-2 (CLS) - P6-1 (GND) SLIDE CLOSE switch is not pressed 10 kΩ or higher
      P6-3 (OPN) - P6-1 (GND) SLIDE OPEN switch is pressed Below 1 Ω
      P6-3 (OPN) - P6-1 (GND) SLIDE OPEN switch is not pressed 10 kΩ or higher

    NG

    REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY) Click here

    OK

    REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here