SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Data List.

    5. Read the Data List according to the display on the GTS.

      Sliding Roof
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Open SW SLIDE OPEN switch signal/ON or OFF

      ON: SLIDE OPEN switch pressed

      OFF: SLIDE OPEN switch not pressed

      		 -
      Close SW SLIDE CLOSE switch signal/ON or OFF

      ON: SLIDE CLOSE switch pressed

      OFF: SLIDE CLOSE switch not pressed

      		 -
      Up SW TILT UP switch signal/ON or OFF

      ON: TILT UP switch pressed

      OFF: TILT UP switch not pressed

      		 -
      Down SW TILT DOWN switch signal/ON or OFF

      ON: TILT DOWN switch pressed

      OFF: TILT DOWN switch not pressed

      		 -
      Hall IC1 Pulse Sliding roof operation signal/LO or HI

      LO: Sliding roof motor not operating

      HI: Sliding roof motor operating

      		 -
      Hall IC1 Status Sliding roof operation signal/NORMAL or LOCK

      NORMAL: Sliding roof motor operating

      LOCK: Sliding roof motor not operating

      		 -
      Hall IC2 Pulse Sliding roof operation signal/LO or HI

      LO: Sliding roof motor not operating

      HI: Sliding roof motor operating

      		 -
      Hall IC2 Status Sliding roof operation signal/NORMAL or LOCK

      NORMAL: Sliding roof motor operating

      LOCK: Sliding roof motor not operating

      		 -
      Ignition (Direct Signal) Ignition switch signal/ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 -
      Ignition (MPX) Ignition switch signal (MPX signal)/ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 -
      Door Courtesy Driver's door courtesy light switch signal/ON or OFF

      ON: Driver's door open

      OFF: Driver's door closed

      		 -
      Key Off Permission Key-off sliding roof operation permit signal/ON or OFF

      ON: Front doors are not opened within 45 seconds after ignition switch turned off

      OFF: Any status except "ON" status

      		 -
      Open Switch Failure (Past) Open switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof open signal failure (Past)

      Not Fail: Sliding roof open signal not fail (Past)

      		 -
      Close Switch Failure (Past) Close switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof close signal failure (Past)

      Not Fail: Sliding roof close signal not fail (Past)

      		 -
      Up Switch Failure (Past) Up switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof tilt up signal failure (Past)

      Not Fail: Sliding roof tilt up signal not fail (Past)

      		 -
      Down Switch Failure (Past) Down switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof tilt down signal failure (Past)

      Not Fail: Sliding roof tilt down signal not fail (Past)

      		 -
      Open Switch Failure (Current) Open switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof open signal failure (Current)

      Not Fail: Sliding roof open signal not fail (Current)

      		 -
      Close Switch Failure (Current) Close switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof close signal failure (Current)

      Not Fail: Sliding roof close signal not fail (Current)

      		 -
      Up Switch Failure (Current) Up switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof tilt up signal failure (Current)

      Not Fail: Sliding roof tilt up signal not fail (Current)

      		 -
      Down Switch Failure (Current) Down switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof tilt down signal failure (Current)

      Not Fail: Sliding roof tilt down signal not fail (Current)

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Sliding Roof
      Tester Display Test Part Control Range Diagnostic Note
      Slide Roof Operate sliding roof CLOS/UP / OFF -
      Slide Roof Operate sliding roof OPN/DWN / OFF -