POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


    1. A01EK8Z

      Using a T25 "TORX" driver, install the rear power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  2. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

    2. Install the temporary bolt to the rear door window regulator assembly.

    3. A01EJYME01
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install the rear door window regulator assembly.

    4. Tighten the temporary bolt and 3 bolts.

      Tech Tips

      Tighten the bolts and the nuts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    5. A01EM7V

      Install the rear door window regulator assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

    2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the power window regulator switch assembly and the rear power window regulator motor connector.

    4. Disconnect the cable from the negative (-) battery terminal.

    5. A01ELPOE01

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrows, in the order shown in the illustration.

    6. A01EJMB

      Install the rear door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    7. A01EK54

      Install the hole plug.

  4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. Install the temporary bolt to the rear door window division bar sub-assembly.

    2. A01EL0LE01
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install the rear door window division bar sub-assembly.

    3. Install the 2 screws.

    4. Tighten the temporary bolt and bolt to install the rear door window division bar sub-assembly.

    5. A01EKAX

      Install the hole plug.

  5. INSTALL REAR DOOR GLASS RUN


    1. A01EJ8N

      Install the rear door glass run.

  6. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A01EMQME01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the 2 connectors.

    5. Engage the 2 clamps.

  7. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01EM92

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.

    2. A01EKW8

      Engage the 2 claws and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.

  8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. for 13 Speakers:


      1. Connect the connector.

    2. A01EL1B

      Engage the 8 clips and install the rear door trim board sub-assembly.

    3. Install the 2 screws.

  9. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01EKM2

      Engage the 2 clips and 5 claws, and install the rear power window regulator switch assembly with rear door armrest base panel.

  10. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01EM4J

      Engage the 3 claws and install the rear door inside handle bezel plug.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here