POWER WINDOW REGULATOR MOTOR (for Front Door) INSTALLATION

Tech Tips

Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.

INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
Note

The regulator arm must be below the intermediate position when installing the front power window regulator motor assembly.
1. Using a T25 "TORX" driver, install the front power window regulator motor assembly with the 3 screws.
  
  Torque:
  
  5.4 N*m { 55 kgf*cm, 48 in.*lbf }
  
  Tech Tips
  
  A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
1. Apply MP grease to the sliding parts of the front door window regulator assembly.
2. Install the temporary bolt to the front door window regulator assembly.
3. Text in Illustration
  
  *1 Temporary Bolt
  
  Temporarily install the front door window regulator assembly.
4. Tighten the temporary bolt and 3 bolts.
  
  Tech Tips
  
  Tighten the bolts and the nuts in the order shown in the illustration.
  
  Torque:
  
  8.0 N*m { 82 kgf*cm, 71 in.*lbf }
5. Install the front door window regulator assembly with the 2 bolts.
  
  Torque:
  
  8.0 N*m { 82 kgf*cm, 71 in.*lbf }
6. Connect the connector.
INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
1. Connect the cable to the negative (-) battery terminal.
2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
4. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
5. Install the front door glass sub-assembly with the 2 bolts.
  
  Torque:
  
  8.0 N*m { 82 kgf*cm, 71 in.*lbf }
INSTALL FRONT DOOR SERVICE HOLE COVER
1. Apply butyl tape to the front door panel.
2. Text in Illustration
  
  *1 Reference Point
  
  Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
3. Attach the front door service hole cover according to the reference points on the front door panel.
  
  Note
  
  Securely install the front door service hole cover preventing wrinkles and air bubbles.
4. Engage the clamp.
5. Install the bolt.
  
  Torque:
  
  8.0 N*m { 82 kgf*cm, 71 in.*lbf }
INSTALL DOOR SIDE AIRBAG SENSOR
1. Check that the ignition switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the vehicle with the bolt.
  
  Torque:
  
  9.0 N*m { 92 kgf*cm, 80 in.*lbf }
  Note
  
  If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
  
  When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
  
  Make sure that the pin (stopper) is securely inserted into the door hole.
  
  Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.
4. Connect the connector to the door side airbag sensor.
  
  Note
  
  When connecting the airbag connector, take care not to damage the airbag wire harness.
  1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.
  2. Be sure to engage the connectors until they are locked (When locking, make sure that a click sound can be heard).
    
    Tech Tips
    
    When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.
5. Check that there is no looseness in the installation parts of the door side airbag sensor.
INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
2. Engage the 2 claws and install the front door inside handle sub-assembly to the rear door trim board sub-assembly.
INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
1. Engage the 10 clips and install the front door trim board sub-assembly.
2. Install the 2 screws.
INSTALL COURTESY LIGHT ASSEMBLY
1. Connect the connector.
2. Engage the claw to install the courtesy light assembly.
INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
1. Connect the connector.
2. Engage the 2 clips and 4 claws, and install the power window regulator master switch assembly with front door armrest base panel.
INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
1. Connect the connector.
2. Engage the 2 clips and 4 claws, and install the power window regulator switch assembly with front door armrest base panel.
INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
1. Engage the 3 claws and install the front door inside handle bezel plug.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INITIALIZE POWER WINDOW CONTROL SYSTEM

Click here
INSPECT SRS WARNING LIGHT

Click here