POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01EK9L

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.

  3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01EIR0

      Using a moulding remover, disengage the 2 clips and 4 claws.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01EIOQ

      Using a moulding remover, disengage the 2 clips and 4 claws.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  5. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01EIV1E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01EMLF

      Remove the 2 screws.

    2. Using a clip remover, disengage the 10 clips.

    3. Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    4. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    5. A01EKW8

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

  7. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01EMBT

      Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.

  8. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Disconnect the connector.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        A01ELCTE09

      2. Push down the white housing lock again and disconnect the connector.

        Tech Tips

        Do not push down part (A) shown in the illustration when disconnecting.

      3. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

        A01EJ7FE02
    4. A01EJ32

      Remove the bolt and door side airbag sensor.

      Note

      Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

  9. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01EMH2

      Disengage the clamp.

    2. Remove the bolt.

    3. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    4. A01EIRD

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A01EM3NE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  11. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. A01EL5DE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    3. Remove the 5 bolts.

    4. Remove the front door window regulator assembly.

    5. Remove the temporary bolt from the front door window regulator assembly.

  12. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01EIQ2

      Using a T25 "TORX" driver, remove the 3 screws and the front power window regulator motor assembly.