ROOF HEADLINING INSTALLATION


  1. INSTALL ROOF HEADLINING ASSEMBLY


    1. A01EJ6K

      Pull the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    2. Engage the 23 fasteners.

      A01EIXG

    3. Install the 3 clips.

    4. Connect the No. 2 antenna cord sub-assembly connector and washer hose to the rear pillar RH.

    5. Connect the No. 2 antenna cord sub-assembly connector and washer hose, and engage the 5 clamps to the front pillar RH.

    6. Connect the No. 1 roof wire connector to the inner rear view mirror.

    7. Connect the No. 1 roof wire connectors and engage the 4 clamps to the front pillar LH.

      A01EJ8CE01
      Text in Illustration
      *1 Clip - -

      Note

      After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

  2. INSTALL VISOR HOLDER


    1. A01ELXO

      Engage the 2 claws.

    2. Push in the visor holder as shown in the illustration.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  3. INSTALL ASSIST GRIP SUB-ASSEMBLY


    1. A01EJOS

      Assemble the assist grip sub-assembly as shown in the illustration.

    2. A01EM1T

      Install the assist grip sub-assembly.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  4. INSTALL REAR ASSIST GRIP ASSEMBLY


    1. A01EKEE

      Assemble the rear assist grip assembly as shown in the illustration.

    2. A01EMGN

      Install the rear assist grip assembly.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  5. INSTALL SPOT LIGHT ASSEMBLY


    1. A01ELUUE01
      Text in Illustration
      *1 Map Light Sub-assembly
      *a Front

      Engage the 8 claws and clamp to connect the spot light housing to the 2 map light sub-assemblies as shown in the illustration.

    2. A01EL0QE01
      Text in Illustration
      *a Front

      Engage the 6 claws to install the spot light housing.

    3. A01EKLNE01
      Text in Illustration
      *a Front

      Engage the 8 claws to install the 2 spot light lenses.

  6. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. Engage the 2 claws.

    2. A01EMJH

      Slide the inner rear view mirror stay holder cover and engage the 2 claws and install the cover as shown in the illustration.

  7. INSTALL VISOR ASSEMBLY LH


    1. A01EIRE

      Install the visor assembly LH with the 2 screws.

  8. INSTALL VISOR BRACKET COVER (for LH Side)


    1. A01EJ04

      Engage the 4 claws and install a new visor bracket cover.

  9. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  10. INSTALL VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  11. INSTALL MAP LIGHT ASSEMBLY


    1. Connect each connector.

    2. A01EKS2E01
      Text in Illustration
      *1 Fastener

      Engage the fastener.

    3. Engage the 2 claws and 2 clips, and install the map light assembly.

  12. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish assembly LH.

    2. Insert the upper edge of the roof side inner garnish assembly LH into the roof headlining. Lift the lower edge of the garnish up and push it in over the 3 stud bolts while ensuring ample clearance.

      Note

      Do not damage the roof headlining assembly or roof side inner garnish assembly.

    3. Engage the 10 clips to install the roof side inner garnish assembly LH with the bolt.

      A01EIX2E01
      Text in Illustration
      *1 Stud Bolt - -
    4. A01ELU9E01
      Text in Illustration
      *1 Protective Tape

      Remove the applied protective tape.

    5. w/ Rear Speaker:


      1. Disconnect the connector.

  13. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Engage the 7 claws and the 5 clips.

    3. Install the deck trim side panel assembly LH with the bolt and clip.

      A01EJPS

  14. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A01EKS4E01
      Text in Illustration
      *1 Protruding Part

      Connect the floor anchor end of the rear seat outer belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding part of the floor panel.

  15. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. A01EJ2H

      Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  16. INSTALL RECLINING REMOTE CONTROL BEZEL LH


    1. A01EKL1

      Engage the 3 claws to install the reclining remote control bezel LH.

  17. INSTALL REAR SEAT ASSEMBLY LH


    1. Place the rear seat assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A01EM4L

      Temporarily install the 2 bolts on the front side of the seat.

    3. A01ELFU

      Temporarily install the 2 bolts on the rear side of the seat.

    4. Install the rear seat assembly LH with the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  18. INSTALL REAR SEAT NO. 2 RECLINING CONTROL CABLE SUB-ASSEMBLY


    1. Remove the rear seat No. 2 reclining control cable from the carpet hole.

      A01EKQ0

    2. Connect the rear seat No. 2 reclining control cable sub-assembly as shown in the illustration.

      A01EM4DE01
      Text in Illustration
      *1 Protective Tape *2 Seat Track Adjusting Handle
    3. A01EMK9

      Engage the 2 claws and connect the rear seat No. 2 reclining control cable sub-assembly as shown in the illustration.

    4. Return the seatback to the upright position.

    5. Pull up the adjuster's lock piece to lock it as shown in the illustration.

      A01EL0OE01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece

      Note

      When pressing the lock piece, make sure the adjuster's spring is not compressed.

  19. INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for LH Side)


    1. A01EJVG

      Engage the guide and 3 claws and install the rear seat outer track bracket cover as shown in the illustration.

  20. INSTALL REAR SEAT INNER TRACK BRACKET COVER (for LH Side)


    1. A01EIZH

      Engage the guide and 3 claws and install the rear seat inner track bracket cover as shown in the illustration.

  21. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)

  22. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  23. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Connect each connector.

    2. Engage the 7 claws and the 6 clips.

    3. Install the deck trim side panel assembly RH with the bolt and clip.

      A01EM0U

  24. CONNECT REAR SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  25. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  26. INSTALL RECLINING REMOTE CONTROL BEZEL RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  27. INSTALL REAR SEAT ASSEMBLY RH


    1. Place the rear seat assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A01EMC9

      Temporarily install the 2 bolts on the front side of the seat.

    3. A01EMPM

      Temporarily install the 3 bolts on the rear side of the seat.

    4. Install the rear seat assembly RH with the 5 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  28. INSTALL REAR SEAT RECLINING CONTROL CABLE SUB-ASSEMBLY (for RH Side)


    1. Connect the rear seat reclining control cable as shown in the illustration.

      A01EIO3

    2. Connect the rear seat reclining control cable sub-assembly as shown in the illustration.

      A01EJ2JE01
      Text in Illustration
      *1 Protective Tape *2 Seat Track Adjusting Handle
    3. A01EJK3

      Engage the 2 claws and connect the rear seat reclining control cable sub-assembly as shown in the illustration.

    4. Return the seatback to the upright position.

    5. Pull up the adjuster's lock piece to lock it as shown in the illustration.

      A01EM2BE01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece

      Note

      When pressing the lock piece, make sure the adjuster's spring is not compressed.

  29. INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for RH Side)


    1. A01EKPX

      Engage the 3 claws and guide, and install the rear seat outer track bracket cover as shown in the illustration.

  30. INSTALL REAR SEAT INNER TRACK BRACKET COVER (for RH Side)


    1. A01EJ0A

      Engage the 3 claws and guide, and install the rear seat inner track bracket cover as shown in the illustration.

  31. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

  32. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

  33. INSTALL REAR FLOOR FINISH PLATE


    1. A01EJJN

      Engage the 4 clips and 2 claws to install the rear floor finish plate.

  34. INSTALL REAR SEAT SUB FLOOR PANEL ASSEMBLY


    1. A01ELM5

      Engage the 2 guides, 2 claws and 5 clips to install the rear seat sub floor panel assembly.

  35. INSTALL NO. 1 DECK BOARD


    1. A01EK32

      Engage the 6 clips to install the No. 1 deck board.

  36. INSTALL DECK SIDE TRIM BOX RH


    1. A01EIQE

      Install the deck side trim box RH with the 4 clips.

  37. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A01EMLZ

      Engage the 2 guides to install the No. 2 deck board sub-assembly.

  38. INSTALL DECK SIDE TRIM BOX LH


    1. A01ELW2

      Install the deck side trim box LH with the 3 clips.

  39. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A01EINV

      Engage the 2 guides to install the No. 3 deck board sub-assembly.

  40. INSTALL DECK BOARD ASSEMBLY


    1. A01EL2J

      Engage the 2 guides to install the deck board assembly.

  41. INSTALL TONNEAU COVER ASSEMBLY


    1. Install the tonneau cover assembly.

  42. INSTALL UPPER CENTER PILLAR GARNISH LH


    1. Pass the floor anchor of the front seat outer belt assembly LH through the upper center pillar garnish LH.

    2. A01EMHL

      Engage the clip.

    3. Install the upper center pillar garnish LH with the screw.

  43. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. A01EL6Q

      Engage the guide, 2 claws and the 2 clips to install the lower center pillar garnish LH as shown in the illustration.

  44. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01EL5J

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  45. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. A01EJOK

      Engage the 3 claws to install the lap belt outer anchor cover.

  46. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EL3EE02
      Text in Illustration
      *1 Alignment mark (Purple)

      Align the alignment mark (Purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  47. INSTALL REAR DOOR SCUFF PLATE LH


    1. A01EMQ6

      Engage the 2 clips and 6 claws to install the rear door scuff plate LH.

  48. INSTALL FRONT PILLAR GARNISH LH


    1. A01EMSEE01

      Engage the 3 guides.

    2. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish RH.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    3. Engage the 2 clips to install the front pillar garnish LH.

  49. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EJYAE01
      Text in Illustration
      *1 Alignment mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  50. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01EJEA

      Engage the 2 clips to install the cowl side trim sub-assembly LH.

    2. Install the clip.

  51. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A01ELE9

      Engage the guide, 3 clips and the 7 claws to install the front door scuff plate LH.

  52. INSTALL UPPER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  53. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  54. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  55. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  56. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01EIR5E01
      Text in Illustration
      *1 Alignment mark (Pink)

      Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  57. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  58. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  59. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01EMPBE01
      Text in Illustration
      *1 Alignment mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  60. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  61. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.