ROOF HEADLINING INSTALLATION

INSTALL ROOF HEADLINING ASSEMBLY
1. Pull the roof headlining assembly into the vehicle through the back door.
  
  Note
  
  Do not damage the roof headlining assembly or body interior.
2. Engage the 23 fasteners.
3. Install the 3 clips.
4. Connect the No. 2 antenna cord sub-assembly connector and washer hose to the rear pillar RH.
5. Connect the No. 2 antenna cord sub-assembly connector and washer hose, and engage the 5 clamps to the front pillar RH.
6. Connect the No. 1 roof wire connector to the inner rear view mirror.
7. Connect the No. 1 roof wire connectors and engage the 4 clamps to the front pillar LH.
  
  Text in Illustration
  
  *1 Clip - -
  
  Note
  
  After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.
INSTALL VISOR HOLDER
1. Engage the 2 claws.
2. Push in the visor holder as shown in the illustration.
  
  Tech Tips
  
  Use the same procedure for the RH side and the LH side.
INSTALL ASSIST GRIP SUB-ASSEMBLY
1. Assemble the assist grip sub-assembly as shown in the illustration.
2. Install the assist grip sub-assembly.
  
  Tech Tips
  
  Use the same procedure for the RH side and the LH side.
INSTALL REAR ASSIST GRIP ASSEMBLY
1. Assemble the rear assist grip assembly as shown in the illustration.
2. Install the rear assist grip assembly.
  
  Tech Tips
  
  Use the same procedure for the RH side and the LH side.
INSTALL SPOT LIGHT ASSEMBLY
1. Engage the 8 claws to install the spot light sub-assembly to the spot light assembly.
2. Engage the 6 claws to install the spot light assembly.
INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
1. Engage the 2 claws.
2. Slide the inner rear view mirror stay holder cover and engage the 2 claws and install the cover as shown in the illustration.
INSTALL VISOR ASSEMBLY LH
1. Install the visor assembly LH with the 2 screws.
INSTALL VISOR BRACKET COVER (for LH Side)
1. Engage the 4 claws and install a new visor bracket cover.
INSTALL VISOR ASSEMBLY RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL VISOR BRACKET COVER (for RH Side)

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL MAP LIGHT ASSEMBLY
1. Connect each connector.
2. Text in Illustration
  
  *1 Fastener
  
  Engage the fastener.
3. Engage the 2 claws and 2 clips, and install the map light assembly.
INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH
1. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish assembly LH.
2. Insert the upper edge of the roof side inner garnish assembly LH into the roof headlining. Lift the lower edge of the garnish up and push it in over the 3 stud bolts while ensuring ample clearance.
  
  Note
  
  Do not damage the roof headlining assembly or roof side inner garnish assembly.
3. Engage the 10 clips to install the roof side inner garnish assembly LH with the bolt.
  
  Text in Illustration
  
  *1 Stud Bolt - -
4. Text in Illustration
  
  *1 Protective Tape
  
  Remove the applied protective tape.
5. w/ Rear Speaker:
  1. Disconnect the connector.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
1. Connect the connector.
2. Engage the 7 claws and the 5 clips.
3. Install the deck trim side panel assembly LH with the bolt and clip.
CONNECT REAR SEAT OUTER BELT ASSEMBLY LH
1. Text in Illustration
  
  *1 Protruding Part
  
  Connect the floor anchor end of the rear seat outer belt assembly and install the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding part of the floor panel.
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)
1. Engage the 2 guides.
2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.
INSTALL RECLINING REMOTE CONTROL BEZEL LH
1. Engage the 3 claws to install the reclining remote control bezel LH.
INSTALL REAR SEAT ASSEMBLY LH
1. Place the rear seat assembly LH in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Temporarily install the 2 bolts on the front side of the seat.
3. Temporarily install the 2 bolts on the rear side of the seat.
4. Install the rear seat assembly LH with the 4 bolts.
  
  Torque:
  
  37 N*m { 377 kgf*cm, 27 ft.*lbf }
INSTALL REAR SEAT NO. 2 RECLINING CONTROL CABLE SUB-ASSEMBLY
1. Remove the rear seat No. 2 reclining control cable from the carpet hole.
2. Connect the rear seat No. 2 reclining control cable sub-assembly as shown in the illustration.
  
  Text in Illustration
  
  *1 Protective Tape *2 Seat Track Adjusting Handle
3. Engage the 2 claws and connect the rear seat No. 2 reclining control cable sub-assembly as shown in the illustration.
4. Return the seatback to the upright position.
5. Pull up the adjuster's lock piece to lock it as shown in the illustration.
  
  Text in Illustration
  
  *1 Adjuster Spring *2 Lock Piece
  
  Note
  
  When pressing the lock piece, make sure the adjuster's spring is not compressed.
INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for LH Side)
1. Engage the guide and 3 claws and install the rear seat outer track bracket cover as shown in the illustration.
INSTALL REAR SEAT INNER TRACK BRACKET COVER (for LH Side)
1. Engage the guide and 3 claws and install the rear seat inner track bracket cover as shown in the illustration.
INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)
INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
1. Connect each connector.
2. Engage the 7 claws and the 6 clips.
3. Install the deck trim side panel assembly RH with the bolt and clip.
CONNECT REAR SEAT OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL RECLINING REMOTE CONTROL BEZEL RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL REAR SEAT ASSEMBLY RH
1. Place the rear seat assembly RH in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Temporarily install the 2 bolts on the front side of the seat.
3. Temporarily install the 3 bolts on the rear side of the seat.
4. Install the rear seat assembly RH with the 5 bolts.
  
  Torque:
  
  37 N*m { 377 kgf*cm, 27 ft.*lbf }
INSTALL REAR SEAT RECLINING CONTROL CABLE SUB-ASSEMBLY (for RH Side)
1. Connect the rear seat reclining control cable as shown in the illustration.
2. Connect the rear seat reclining control cable sub-assembly as shown in the illustration.
  
  Text in Illustration
  
  *1 Protective Tape *2 Seat Track Adjusting Handle
3. Engage the 2 claws and connect the rear seat reclining control cable sub-assembly as shown in the illustration.
4. Return the seatback to the upright position.
5. Pull up the adjuster's lock piece to lock it as shown in the illustration.
  
  Text in Illustration
  
  *1 Adjuster Spring *2 Lock Piece
  
  Note
  
  When pressing the lock piece, make sure the adjuster's spring is not compressed.
INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for RH Side)
1. Engage the 3 claws and guide, and install the rear seat outer track bracket cover as shown in the illustration.
INSTALL REAR SEAT INNER TRACK BRACKET COVER (for RH Side)
1. Engage the 3 claws and guide, and install the rear seat inner track bracket cover as shown in the illustration.
INSTALL REAR SEAT CENTER HEADREST ASSEMBLY
INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)
INSTALL REAR FLOOR FINISH PLATE
1. Engage the 4 clips and 2 claws to install the rear floor finish plate.
INSTALL REAR SEAT SUB FLOOR PANEL ASSEMBLY
1. Engage the 2 guides, 2 claws and 5 clips to install the rear seat sub floor panel assembly.
INSTALL NO. 1 DECK BOARD
1. Engage the 6 clips to install the No. 1 deck board.
INSTALL DECK SIDE TRIM BOX RH
1. Install the deck side trim box RH with the 4 clips.
INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY
1. Engage the 2 guides to install the No. 2 deck board sub-assembly.
INSTALL DECK SIDE TRIM BOX LH
1. Install the deck side trim box LH with the 3 clips.
INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
1. Engage the 2 guides to install the No. 3 deck board sub-assembly.
INSTALL DECK BOARD ASSEMBLY
1. Engage the 2 guides to install the deck board assembly.
INSTALL TONNEAU COVER ASSEMBLY
1. Install the tonneau cover assembly.
INSTALL UPPER CENTER PILLAR GARNISH LH
1. Pass the floor anchor of the front seat outer belt assembly LH through the upper center pillar garnish LH.
2. Engage the clip.
3. Install the upper center pillar garnish LH with the screw.
INSTALL LOWER CENTER PILLAR GARNISH LH
1. Engage the guide, 2 claws and the 2 clips to install the lower center pillar garnish LH as shown in the illustration.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
1. Install the floor end of the front seat outer belt assembly with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
2. Check if the ELR locks.
  
  Note
  
  The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
1. Engage the 3 claws to install the lap belt outer anchor cover.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
1. Text in Illustration
  
  *1 Alignment mark (Purple)
  
  Align the alignment mark (Purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE LH
1. Engage the 2 clips and 6 claws to install the rear door scuff plate LH.
INSTALL FRONT PILLAR GARNISH LH
1. Engage the 3 guides.
2. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish RH.
  
  Tech Tips
  
  Tape the needle-nosed pliers tip before use.
3. Engage the 2 clips to install the front pillar garnish LH.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Text in Illustration
  
  *1 Alignment mark (Yellow)
  
  Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
1. Engage the 2 clips to install the cowl side trim sub-assembly LH.
2. Install the clip.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Engage the guide, 3 clips and the 7 claws to install the front door scuff plate LH.
INSTALL UPPER CENTER PILLAR GARNISH RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL LOWER CENTER PILLAR GARNISH RH

Tech Tips

Use the same procedure for the RH side and the LH side.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *1 Alignment mark (Pink)
  
  Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL FRONT PILLAR GARNISH RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *1 Alignment mark (White)
  
  Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure for the RH side and the LH side.