REAR POWER OUTLET SOCKET REMOVAL


  1. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  2. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  3. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  4. REMOVE DECK BOARD ASSEMBLY


    1. A01EL2J

      Disengage the 2 guides and remove the deck board assembly.

  5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A01EINV

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  6. REMOVE DECK SIDE TRIM BOX LH


    1. A01ELW2

      Remove the 3 clips and remove the deck side trim box LH.

  7. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A01EMLZ

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  8. REMOVE DECK SIDE TRIM BOX RH


    1. A01EIQE

      Remove the 4 clips and remove the deck side trim box RH.

  9. REMOVE NO. 1 DECK BOARD


    1. A01EK32

      Disengage the 6 clips and remove the No. 1 deck board.

  10. REMOVE REAR SEAT SUB FLOOR PANEL ASSEMBLY


    1. A01ELM5

      Disengage the 2 claws, 2 guides and 5 clips, and remove the rear seat sub floor panel assembly.

  11. REMOVE REAR FLOOR FINISH PLATE


    1. A01EJJN

      Disengage the 2 claws and 4 clips, and remove the rear floor finish plate.

  12. REMOVE REAR SEAT HEADREST ASSEMBLY

  13. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY

  14. REMOVE REAR SEAT INNER TRACK BRACKET COVER


    1. A01EM8W

      Disengage the 3 claws and guide, and remove the rear seat inner track bracket cover as shown in the illustration.

  15. REMOVE REAR SEAT OUTER TRACK BRACKET COVER


    1. A01EKLF

      Disengage the 3 claws and guide, and remove the rear seat outer track bracket cover as shown in the illustration.

  16. DISCONNECT REAR SEAT RECLINING CONTROL CABLE SUB-ASSEMBLY


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A01EJOCE01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece
    2. A01EKXEE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A01EK6GE01
      Text in Illustration
      *1 Protective Tape *2 Seat Track Adjusting Handle

    4. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable sub-assembly as shown in the illustration.

      A01ELATE01
      Text in Illustration
      *1 Protective Tape - -

  17. REMOVE REAR SEAT ASSEMBLY RH


    1. A01EMPM

      Remove the 3 bolts on the rear side of the seat.

    2. A01EMC9

      Remove the 2 bolts on the front side of the rear seat assembly RH.

    3. Remove the rear seat assembly RH.

      Note

      Be careful not to damage the vehicle body.

  18. REMOVE RECLINING REMOTE CONTROL BEZEL RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  19. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  20. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  21. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the bolt and clip.

    2. Disengage the 7 claws and 6 clips.

    3. Disconnect each connector and remove the deck trim side panel assembly RH.

      A01EM0U

  22. REMOVE REAR POWER POINT SOCKET ASSEMBLY


    1. A01ELSHE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws and remove the rear power point socket assembly as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE REAR POWER POINT SOCKET COVER


    1. A01EM28

      Disengage the 2 claws and remove the rear power point socket cover.