FRONT SEAT CUSHION HEATER REMOVAL


  1. REMOVE FRONT SEAT HEADREST ASSEMBLY

  2. REMOVE FRONT SEAT REAR OUTER TRACK COVER


    1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.

    2. A01EK4X

      Disengage the 2 claws and remove the front seat rear outer track cover.

  3. REMOVE FRONT SEAT REAR INNER TRACK COVER


    1. A01EKMV

      Disengage the 2 claws and remove the front seat rear inner track cover.

  4. REMOVE FRONT SEAT ASSEMBLY


    1. A01ELZQ

      Remove the 2 bolts on rear side of the front seat assembly.

    2. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    3. A01ELJK

      Remove the 2 bolts on front side of the front seat assembly.

    4. Operate the slide and vertical power seat switch knob and move the front seat assembly to the center position. Also, operate the reclining power seat switch knob and move the front seatback assembly to the upright position.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    6. Disconnect each connector under the front seat assembly.

    7. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  5. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A01EK59

      Using a moulding remover, disengage the 4 claws and remove the reclining power seat switch knob.

  6. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A01EJRB

      Using a moulding remover, disengage the 2 claws as shown in the illustration.

    2. A01EJ96

      Using a moulding remover, disengage the 2 claws and remove the slide and vertical power seat switch knob as shown in the illustration.

  7. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. A01EM3G

      Disengage the 2 hooks.

    2. A01EJB8

      Remove the 5 screws.

    3. Disengage the claw.

    4. Disengage the guide and remove the front seat cushion shield assembly.

    5. A01ELRX

      Disconnect the connector from the front power seat lumbar switch.

  8. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    1. Disconnect each connector and disengage each clamp.

    2. A01EJNR

      Remove the nut and the front seat inner belt assembly.

  9. REMOVE FRONT INNER SEAT CUSHION SHIELD


    1. A01EJMW

      Remove the screw.

    2. Disengage the claw.

    3. A01EJGL

      Disengage the guide and remove the front inner seat cushion shield as shown in the illustration.

  10. REMOVE POSITION CONTROL ECU AND SWITCH ASSEMBLY (for Driver Side)


    1. A01EK8D

      Remove the 3 screws.

    2. Disengage the guide.

    3. A01ELIF

      Disconnect the 2 connectors and remove the position control ECU and switch assembly.

  11. REMOVE FRONT POWER SEAT SWITCH RH (for Front Passenger Side)


    1. A01EIX7

      Remove the 3 screws.

    2. Disconnect the connector and remove the power seat switch.

  12. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. A01ELW7

      Disengage the 4 hooks.

    2. A01EJ6L

      Disengage each clamp.

    3. Disconnect the connector.

    4. Using a clip remover, remove the 2 clips.

      A01ELBU

    5. Disengage each hook as shown in the illustration.

    6. A01ELK5

      Remove the separate type front seat cushion cover with pad as shown in the illustration.

  13. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. Remove the 18 hog rings and the separate type front seat cushion cover.

      A01EK63
    2. A01EM5K

      Cut off the 25 tack pins that fasten the seat heater, and then remove the separate type front seat cushion heater assembly from the separate type front seat cushion cover.