FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Mirror L / Data List.

    5. Read the Data List according to the display on the GTS.

      Mirror L
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Seat Memory Switch1 M1 switch / ON or OFF

      ON: M1 switch on

      OFF: M1 switch off

      		 -
      Seat Memory Switch2 M2 switch / ON or OFF

      ON: M2 switch on

      OFF: M2 switch off

      		 -
      Seat Memory Switch3* M3 switch / ON or OFF

      ON: M3 switch on

      OFF: M3 switch off

      		 Not applicable
      Seat Memory Set SW SET switch / ON or OFF

      ON: SET switch on

      OFF: SET switch off

      		 -
      +B Voltage Input Value Power supply for outer mirror control ECU assembly LH / MIN: 0 V, MAX: 19.98 V Within range from 11 to 14 V -

      • *: Although the item is displayed on the GTS, it is not applicable to this vehicle.

    6. Enter the following menus: Body Electrical / Driver Seat / Data List.

    7. Read the Data List according to the display on the GTS.

      Driver Seat
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Reclining Rear Reclining switch signal (Rearward) / ON or OFF

      ON: Reclining switch (Rearward) on

      OFF: Reclining switch (Rearward) off

      		 -
      Reclining Front Reclining switch signal (Forward) / ON or OFF

      ON: Reclining switch (Forward) on

      OFF: Reclining switch (Forward) off

      		 -
      Front Vertical Down Front vertical switch signal (Downward) / ON or OFF

      ON: Front vertical switch (Downward) on

      OFF: Front vertical switch (Downward) off

      		 -
      Front Vertical Up Front vertical switch signal (Upward) / ON or OFF

      ON: Front vertical switch (Upward) on

      OFF: Front vertical switch (Upward) off

      		 -
      Lifter Switch Down Lifter switch signal (Downward) / ON or OFF

      ON: Lifter switch (Downward) on

      OFF: Lifter switch (Downward) off

      		 -
      Lifter Switch Up Lifter switch signal (Upward) / ON or OFF

      ON: Lifter switch (Upward) on

      OFF: Lifter switch (Upward) off

      		 -
      Slide Rear Slide switch signal (Rearward) / ON or OFF

      ON: Slide switch (Rearward) on

      OFF: Slide switch (Rearward) off

      		 -
      Slide Front Slide switch signal (Forward) / ON or OFF

      ON: Slide switch (Forward) on

      OFF: Slide switch (Forward) off

      		 -
      Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem

      Mem: Memorized

      Not Mem: Not memorized

      		 -
      Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem

      Mem: Memorized

      Not Mem: Not memorized

      		 -
      Seat Memory No3* Seat position memorized with M3 switch / Mem or Not Mem

      Mem: Memorized

      Not Mem: Not memorized

      		 Not applicable
      Ignition Switch Communication state of ignition switch signal / ON or OFF

      ON: Ignition switch ON signal received

      OFF: Ignition switch off signal not received

      		 -
      P Switch Park state signal / ON or OFF

      ON: Shift lever in P

      OFF: Shift lever in a position other than P

      		 -
      Parking Brake SW Parking brake switch status / ON or OFF

      ON: Parking brake applied

      OFF: Parking brake released

      		 -
      Vehicle Speed Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
      Power Voltage Power supply for position control ECU and switch assembly / min: 0.95 V, max: 20.84 V Within range from 11 V to 14 V -
      Slide Position Seat sliding position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Position Seat reclining position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Front Vertical Position Seat front vertical position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Position Seat lifter position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Slide Pos Mem No1 Seat slide position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Pos Mem No1 Seat reclining position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Frnt Vrtcl Pos Mem No1 Front vertical position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Pos Mem No1 Lifter position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Slide Pos Mem No2 Seat slide position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Pos Mem No2 Seat reclining position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Frnt Vrtcl Pos Mem No2 Front vertical position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Pos Mem No2 Lifter position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Slide Pos Mem No3* Seat slide position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Reclining Pos Mem No3* Seat reclining position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Frnt Vrtcl Pos Mem No3* Front vertical position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Lifter Pos Mem No3* Lifter position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Headrest Switch UP* Headrest switch signal (UP) / ON or OFF

      ON: Headrest switch (UP) on

      OFF: Headrest switch (UP) off

      		 Not applicable
      Headrest Switch Down* Headrest switch signal (Down) / ON or OFF

      ON: Headrest switch (Down) on

      OFF: Headrest switch (Down) off

      		 Not applicable
      Motor Status State of slide motor control / STANDBY, MOVING, LOCK

      STANDBY: Slide motor idle

      MOVING: Slide motor moving

      LOCK: Slide motor locked

      		 -
      Lifter Initialize Flag Seat lifter limit position memory / ON or OFF

      ON: Memorized

      OFF: Not memorized

      		 -
      Front Vertical Init Flag Seat front vertical limit position memory / ON or OFF

      ON: Memorized

      OFF: Not memorized

      		 -
      Reclining Position Init Flg Seat reclining limit position memory / ON or OFF

      ON: Memorized

      OFF: Not memorized

      		 -
      Slide Position Init Flag Seat slide limit position memory / ON or OFF

      ON: Memorized

      OFF: Not memorized

      		 -
      Slide Position Front Limit Seat sliding position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Slide Position Rear Limit Seat slide position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Position Front Limit Seat reclining position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Position Rear Limit Seat reclining position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Front Vertical UP Limit Seat front vertical position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Front Vertical Down Limit Seat front vertical position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Position UP Limit Seat lifter position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Position Down Limit Seat lifter position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Shift P sw(PMN)* Park state signal / ON or OFF

      ON: Shift lever in P

      OFF: Shift lever in a position other than P

      		 Not applicable
      Memory Button Buzzer Request Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT

      OFF: Buzzer does not sound

      MOVE: Request to sound buzzer when starting memory replay

      REGISTRY: Request to sound buzzer when starting memory registration

      CANCEL: Request to sound buzzer when canceling memory call registration

      REG NG: Request to sound buzzer when memory call registration not possible

      REG WAIT: Request to sound buzzer when starting memory call cabin scan

      		 -
      Driver Seat Request Command Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET

      OFF: No instruction

      MEMORY: Request to memorize

      MEM MOV: Request to recall memory

      MEM SOD: Request to replay

      RET MOV: Request to return

      AWY MOV: Request to move away

      AWY SOD: Request to recall away position memory

      MEM AWY: Request to recall memorized position of seatback

      MEM RET: Request to restore seatback to memorized position

      		 -
      Driver Seat POS REQ Seat memory switch operation value / OFF, MEM1, MEM2, MEM3*, DRV1*, DRV2* or DRV3*

      OFF: No operation

      MEM1: M1 switch operation status

      MEM2: M2 switch operation status

      MEM3: M3 switch operation status*

      DRV1: Other 1 operation status*

      DRV2: Other 2 operation status*

      DRV3: Other 3 operation status*

      		 -
      Away Move Range Scale The seat travel distance for the power easy access system / NONE, SMALL, STANDARD or LONG

      NONE: Seat travel distance none

      SMALL: Seat travel distance short

      STANDARD: Seat travel distance normal

      LONG: Seat travel distance long

      		 -
      Return Move Return function / NOT AVL or AVAIL

      NOT AVL: Not available

      AVAIL: Available

      		 -
      Return & Away Function Return & away function / NOT AVL or AVAIL

      NOT AVL: Not available

      AVAIL: Available

      		 -
      Driver Seat Buckle SW Driver seat belt buckle switch / ON or OFF

      ON: Driver seat belt fastened

      OFF: Driver seat belt unfastened

      		 -
      Return Position Return position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Sensor Power Voltage Sensor Power Voltage / min: 0 V, max: 19.89 V Within range from 11 to 14 V -
      Number of Trouble Codes Number of trouble codes / min.: 0 or max.: 255 Number of DTCs will be displayed -

      • *: Although the item is displayed on the GTS, it is not applicable to this vehicle.

    8. Enter the following menus: Body Electrical / Main Body / Data List.

    9. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door Courtesy SW Front door courtesy light switch assembly LH signal / ON or OFF

      ON: Driver door open

      OFF: Driver door closed

      		 -
      Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal / ON or OFF

      ON: Lock side of door control switch (power window regulator master switch assembly) pushed

      OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed

      		 -
      Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal / ON or OFF

      ON: Unlock side of door control switch (power window regulator master switch assembly) pushed

      OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed

      		 -
      Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3*

      NONE: No switches linked with key ID1

      MEM SW1: M1 switch linked with key ID1

      MEM SW2: M2 switch linked with key ID1

      MEM SW3: M3 switch linked with key ID1*

      		 -
      Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3*

      NONE: No switches linked with key ID2

      MEM SW1: M1 switch linked with key ID2

      MEM SW2: M2 switch linked with key ID2

      MEM SW3: M3 switch linked with key ID2*

      		 -
      Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3*

      NONE: No switches linked with key ID3

      MEM SW1: M1 switch linked with key ID3

      MEM SW2: M2 switch linked with key ID3

      MEM SW3: M3 switch linked with key ID3*

      		 -
      Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3*

      NONE: No switches linked with key ID4

      MEM SW1: M1 switch linked with key ID4

      MEM SW2: M2 switch linked with key ID4

      MEM SW3: M3 switch linked with key ID4*

      		 -
      Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3*

      NONE: No switches linked with key ID5

      MEM SW1: M1 switch linked with key ID5

      MEM SW2: M2 switch linked with key ID5

      MEM SW3: M3 switch linked with key ID5*

      		 -
      Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3*

      NONE: No switches linked with key ID6

      MEM SW1: M1 switch linked with key ID6

      MEM SW2: M2 switch linked with key ID6

      MEM SW3: M3 switch linked with key ID6*

      		 -
      Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3*

      NONE: No switches linked with key ID7

      MEM SW1: M1 switch linked with key ID7

      MEM SW2: M2 switch linked with key ID7

      MEM SW3: M3 switch linked with key ID7*

      		 -
      Driver Seat Memory1 Seat position memorized with M1 switch / OFF or ON

      OFF: Not memorized

      ON: Memorized

      		 -
      Driver Seat Memory2 Seat position memorized with M2 switch / OFF or ON

      OFF: Not memorized

      ON: Memorized

      		 -
      Driver Seat Memory3* Seat position memorized with M3 switch / OFF or ON

      OFF: Not memorized

      ON: Memorized

      		 Not applicable

      • *: Although the item is displayed on the GTS, it is not applicable to this vehicle.

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Driver Seat / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Driver Seat
      Tester Display Test Part Control Range Diagnostic Note
      Seat Reclining Seat reclining operation OFF/Front/Rear -
      Front Vertical Operation Seat front vertical operation OFF/Up/Down -
      Lifter Operation Seat lifter operation OFF/Up/Down -
      Seat Slide Operation Seat slide operation OFF/Front/Rear -
      Buzzer Buzzer operation OFF/ON -