AIRBAG SYSTEM, Diagnostic DTC:B1805/52, B1806/52, B1807/52, B1808/52

DTC Code DTC Name
B1805/52 Short in Front Passenger Side Squib Circuit
B1806/52 Open in Front Passenger Side Squib Circuit
B1807/52 Short to GND in Front Passenger Side Squib Circuit
B1808/52 Short to B+ in Front Passenger Side Squib Circuit

DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor assembly and front passenger airbag assembly.

The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1805/52

  • The center airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit during primary check.

  • Front passenger side squib malfunction

  • Center airbag sensor assembly malfunction

  • Instrument panel wire

  • Instrument panel wire assembly

  • Front passenger airbag assembly (Front passenger side squib)

  • Center airbag sensor assembly
B1806/52

  • The center airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit.

  • Front passenger side squib malfunction

  • Center airbag sensor assembly malfunction

  • Instrument panel wire

  • Instrument panel wire assembly

  • Front passenger airbag assembly (Front passenger side squib)

  • Center airbag sensor assembly
B1807/52

  • The center airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib circuit.

  • Front passenger side squib malfunction

  • Center airbag sensor assembly malfunction

  • Instrument panel wire

  • Instrument panel wire assembly

  • Front passenger airbag assembly (Front passenger side squib)

  • Center airbag sensor assembly
B1808/52

  • The center airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit.

  • Front passenger side squib malfunction

  • Center airbag sensor assembly malfunction

  • Instrument panel wire

  • Instrument panel wire assembly

  • Front passenger airbag assembly (Front passenger side squib)

  • Center airbag sensor assembly

WIRING DIAGRAM

A01EK1JE85

INSPECTION PROCEDURE

Tech Tips


  • Perform the simulation method by selecting check mode (Signal Check) using the GTS Click here.

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Click here.

PROCEDURE


  1. CHECK CONNECTORS


    1. A01EM0SE01
      Text in Illustration
      *1 Front Passenger Side Squib
      *2 Center Airbag Sensor Assembly
      *3 Instrument Panel Wire Assembly
      *4 Instrument Panel Wire

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the front passenger airbag assembly and center airbag sensor assembly. Also check that the connectors that link the instrument panel wire and instrument panel wire assembly are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the front passenger airbag assembly and center airbag sensor assembly. Also disconnect the instrument panel wire from the instrument panel wire assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the instrument panel wire assembly connector (on the front passenger airbag assembly side) is not damaged.

      OK
      The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

    7. Check that the short springs for the instrument panel wire and instrument panel wire assembly with the activation prevention mechanism are not deformed or damaged.

      OK
      The short springs are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  2. CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)


    1. A01ELUFE01
      Text in Illustration
      *1 Front Passenger Side Squib
      *2 Center Airbag Sensor Assembly
      *3

      Front view of wire harness connector

      (to Front Passenger Airbag Assembly)
      *4 Connector E
      *5 Color: Orange

      Connect the instrument panel wire to the instrument panel wire assembly and center airbag sensor assembly.

    2. Connect SST (resistance 2.1 Ω) to connector E (orange connector).

      CAUTION:

      Never connect an electrical tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      OK
      DTCs B1805, B1806, B1807, B1808 or 52 is not output.

      Tech Tips

      Codes other than DTCs B1805, B1806, B1807, B1808 and 52 may be output at this time, but they are not related to this check.


    NG

    CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT Click here

    OK

    REPLACE FRONT PASSENGER AIRBAG ASSEMBLY Click here

  3. CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT


    1. A01EIW5E01
      Text in Illustration
      *1 Front Passenger Side Squib
      *2 Center Airbag Sensor Assembly
      *3

      Front view of wire harness connector

      (to Front Passenger Airbag Assembly)
      *4 Connector E
      *5 Color: Orange

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect SST from connector E.

    4. Disconnect the instrument panel wire from the center airbag sensor assembly.

    5. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        G1-1 (P+) - Body ground Ignition switch ON Below 1 V
        G1-2 (P-) - Body ground Ignition switch ON Below 1 V

    6. Check for an open in the circuit.


      1. Turn the ignition switch off.

      2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        G1-1 (P+) - G1-2 (P-) Always Below 1 Ω

    7. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        G1-1 (P+) - Body ground Always 1 MΩ or higher
        G1-2 (P-) - Body ground Always 1 MΩ or higher

    8. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B Click here.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        G1-1 (P+) - G1-2 (P-) Always 1 MΩ or higher

    9. Restore the released activation prevention mechanism of connector B to the original condition.


    NG

    CHECK INSTRUMENT PANEL WIRE Click here

    OK

  4. CHECK CENTER AIRBAG SENSOR ASSEMBLY


    1. A01EMH8E01
      Text in Illustration
      *1 Front Passenger Side Squib
      *2 Center Airbag Sensor Assembly

      Connect the connectors to the front passenger airbag assembly and center airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1805, B1806, B1807, B1808 or 52 is not output.

      Tech Tips

      Codes other than DTCs B1805, B1806, B1807, B1808 and 52 may be output at this time, but they are not related to this check.


    NG

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  5. CHECK INSTRUMENT PANEL WIRE


    1. A01EJCEE08
      Text in Illustration
      *1 Front Passenger Side Squib
      *2 Center Airbag Sensor Assembly
      *3 Instrument Panel Wire Assembly
      *4 Instrument Panel Wire
      *5

      Front view of wire harness connector

      (to Instrument Panel Wire Assembly)
      *6 Connector C

      Disconnect the instrument panel wire assembly from the instrument panel wire.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        DG1-1 (P+) - Body ground Ignition switch ON Below 1 V
        DG1-2 (P-) - Body ground Ignition switch ON Below 1 V

    3. Check for an open in the circuit.


      1. Turn the ignition switch off.

      2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        DG1-1 (P+) - DG1-2 (P-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        DG1-1 (P+) - Body ground Always 1 MΩ or higher
        DG1-2 (P-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B Click here.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        DG1-1 (P+) - DG1-2 (P-) Always 1 MΩ or higher

    NG

    REPLACE INSTRUMENT PANEL WIRE

    OK

  6. CHECK INSTRUMENT PANEL WIRE ASSEMBLY


    1. A01EMQAE01
      Text in Illustration
      *1 Front Passenger Side Squib
      *2 Center Airbag Sensor Assembly
      *3 Instrument Panel Wire Assembly
      *4 Instrument Panel Wire
      *5

      Front view of wire harness connector

      (to Front Passenger Airbag Assembly)
      *6 Connector E
      *7 Color: Orange

      Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        G1-1 (P+) - Body ground Ignition switch ON Below 1 V
        G1-2 (P-) - Body ground Ignition switch ON Below 1 V

    2. Check for an open in the circuit.


      1. Turn the ignition switch off.

      2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        G1-1 (P+) - G1-2 (P-) Always Below 1 Ω

    3. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        G1-1 (P+) - Body ground Always 1 MΩ or higher
        G1-2 (P-) - Body ground Always 1 MΩ or higher

    4. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector D Click here.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        G1-1 (P+) - G1-2 (P-) Always 1 MΩ or higher

    NG

    REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

    OK

    USE SIMULATION METHOD TO CHECK Click here