ENGINE HOOD COURTESY SWITCH INSTALLATION


  1. INSTALL SECURITY COURTESY SWITCH (HOOD LOCK ASSEMBLY)


    1. A01ELDL

      Apply MP grease to the sliding areas of the lock.

    2. Connect the hood lock control cable.

    3. A01EJFGE01

      Install the hood lock assembly with the 3 bolts.

      Torque:
      <A> Centering Bolt
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Torque:
      <A> Standard Bolt
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
      Torque:
      <B>
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Connect the connector.

    5. A01EJ4W

      Install a new hood lock nut cap.

  2. INSTALL LOW PITCHED HORN ASSEMBLY


    1. Install the low pitched horn assembly with the bolt.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. Connect the connector.

  3. INSTALL RADIATOR GRILLE


    1. Engage the 6 claws.

    2. Install the 3 clips.

    3. Install the radiator grille with the 2 bolts.

  4. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 12 clips.

  5. INSPECT HOOD SUB-ASSEMBLY


    1. Check that the clearance measurements of areas *1 through *4 are within each standard range.

      A01EIQXE01
      Standard Clearance
      Area Measurement Area Measurement
      *1 6.9 to 9.9 mm (0.272 to 0.390 in.) *3 2.8 to 5.8 mm (0.110 to 0.228 in.)
      *2 7.6 to 10.6 mm (0.299 to 0.417 in.) *4 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

  6. ADJUST HOOD SUB-ASSEMBLY


    1. Horizontally and vertically adjust the hood.


      1. A01EK3E

        Loosen the 4 hinge bolts of the hood.

      2. Adjust the clearance between the hood and front fender by moving the hood.

      3. Tighten the 4 hinge bolts after the adjustment.

        Torque:
        13 N*m  { 133 kgf*cm, 10 ft.*lbf }

    2. Adjust the height of the front end of the hood using the cushion rubbers.


      1. A01EJ5F

        Adjust the 2 cushion rubbers so that the heights of the hood and fender are aligned.

        Tech Tips

        Raise or lower the front end of the hood by turning the 2 cushion rubbers.

    3. Adjust the hood lock.


      1. A01EK7KE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, remove the hood lock nut cap.

        Tech Tips

        Tape the screwdriver tip before use.

      2. A01EISME01

        Loosen the 3 bolts.

      3. Tighten the bolts after the adjustment.

        Torque:
        <A>
        7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
        Torque:
        <B>
        8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      4. Check that the striker can engage with the hood lock smoothly.

    4. A01EJ5M

      Install a new hood lock nut cap.