LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Key Unlock Warning SW*1 Key unlock warning switch signal/ON or OFF

      ON: Key in ignition key cylinder

      OFF: No key in ignition key cylinder

      		 -
      ACC SW Ignition switch or engine switch ACC signal/ON or OFF

      ON: Ignition switch ACC

      OFF: Ignition switch off

      		 -
      IG SW Ignition switch or engine switch IG signal/ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 -
      FR Door Courtesy SW Front door courtesy light switch RH signal/ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Courtesy SW Front door courtesy light switch LH signal/ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      RR Door Courtesy SW Rear door courtesy light switch RH signal/ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH signal/ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      		 -
      Luggage Courtesy SW Back door courtesy switch signal/ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      FR Door Lock Pos Driver side door unlock detection switch signal/ON or OFF

      ON: Driver side door unlocked

      OFF: Driver side door locked

      		 -
      FL Door Lock Pos Front passenger side door unlock detection switch signal/ON or OFF

      ON: Front passenger side door unlocked

      OFF: Front passenger side door locked

      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch signal/ON or OFF

      ON: Rear door RH unlocked

      OFF: Rear door RH locked

      		 When checking this item, make sure to check it with the rear door LH locked.
      RL-Door Lock Pos SW Rear door LH unlock detection switch signal/ON or OFF

      ON: Rear door LH unlocked

      OFF: Rear door LH locked

      		 When checking this item, make sure to check it with the rear door RH locked.

      • *1: w/o Smart Entry and Start System

  2. ACTIVE TEST

    Tech Tips

    Using GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (desired system) / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Illuminated Entry System Roof console box assembly, step or spot light assembly and transponder key amplifier*1/engine switch illumination*2 ON/OFF Interior light switch in DOOR position and all doors closed
      Relay for Interior Light Auto Cut Function DOME CUT relay ON/OFF -
      Entry&Start
      Tester Display Test Part Control Range Diagnostic Note
      Power/Engine SW Light Engine switch illumination OFF/ON

      When performing this Active Test, make sure the following condition is met:

      The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.

      • *1: w/o Smart Entry and Start System

      • *2: w/ Smart Entry and Start System