SMART ENTRY AND START SYSTEM (for Entry Function), Diagnostic DTC:B27A2

DTC Code DTC Name
B27A2 Open in Front Passenger Side Electrical Antenna Circuit

DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and sends it to the door electrical key oscillator built into the front door outside handle assembly (for front passenger side) at 0.25-second intervals. To detect a key near the front passenger door, the front door outside handle assembly (for front passenger side) creates a detection area with a radius of approximately 1.0 m (3.28 ft.) from the front passenger door at 0.25-second intervals.

DTC B27A2 is detected by the certification ECU (smart key ECU assembly) if an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger side) terminals (between CLG2 and ANT1, or CG2B and ANT2).

DTC No. DTC Detection Condition Trouble Area
B27A2 Open circuit detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger side) terminals (between CLG2 and ANT1, or CG2B and ANT2).

  • Front door outside handle assembly (for front passenger side)

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

WIRING DIAGRAM

A01EM63E02

INSPECTION PROCEDURE

Note


  • The smart entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the smart entry and start system (for entry function) after confirming that the communication system is functioning properly.

  • Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

PROCEDURE


  1. CHECK CONNECTOR CONNECTION CONDITION


    1. Turn the engine switch off.

    2. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the front door outside handle assembly (for front passenger side).

      OK
      Connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)


    1. Disconnect the certification ECU (smart key ECU assembly) connector.

    2. A01ELGWE08
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))
      *2

      Front view of wire harness connector

      (to Front Door Outside Handle Assembly (for Front Passenger Side))

      Disconnect the front door outside handle assembly (for front passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D25-5 (CLG2) - z4-6 (ANT1) Always Below 1 Ω
      D25-6 (CG2B) - z4-3 (ANT2) Always Below 1 Ω
      D25-5 (CLG2) - Body ground Always 10 kΩ or higher
      D25-6 (CG2B) - Body ground Always 10 kΩ or higher
      z4-6 (ANT1) - Body ground Always 10 kΩ or higher
      z4-3 (ANT2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - BODY GROUND)


    1. A01EIW9E05
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Front Door Outside Handle Assembly (for Front Passenger Side))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z4-2 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (DOOR ELECTRICAL KEY OSCILLATOR SIGNAL OUTPUT)


    1. A01ELPLE02
      Text in Illustration
      *1

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      Reconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance and check for pulses according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D25-15 (E) - Body ground Always Below 1 Ω
      Standard
      Tester Connection Condition Specified Condition
      D25-5 (CLG2) - D25-15 (E)

      • Engine switch off

      • All door closed

      • Key not in cabin

      		 No pulse generation
      D25-5 (CLG2) - D25-15 (E)

      • Engine switch off

      • All door closed

      • Key not in cabin

      • All doors locked by wireless lock function

      		 Pulse generation
      D25-6 (CG2B) - D25-15 (E)

      • Engine switch off

      • All door closed

      • Key not in cabin

      		 No pulse generation
      D25-6 (CG2B) - D25-15 (E)

      • Engine switch off

      • All door closed

      • Key not in cabin

      • All doors locked by wireless lock function

      		 Pulse generation

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

  5. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side)


    1. Replace the front door outside handle assembly (for front passenger side) Click here.


    NEXT

  6. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Recheck for DTCs.

      OK
      DTC B27A2 is not output.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)