UNLOCK WARNING SWITCH INSTALLATION


  1. INSTALL UNLOCK WARNING SWITCH


    1. A01EKMH

      Engage the 2 claws and install the unlock warning switch to the steering column upper bracket.

    2. Extract the key.

    3. A01EL0Y

      Connect the connector.

  2. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. A01EMNGE01
      Text in Illustration
      *1 Clamp
      *2 Claw

      Using pliers, expand the clamp.

    2. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

    3. Return the clamp to its original position.

    4. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  3. INSTALL UPPER STEERING COLUMN COVER


    1. A01EK5A

      Engage the 4 clips and 2 guides to install the upper steering column cover onto the instrument panel cluster finish panel.

    2. A01EJEM

      Engage the claw to install the upper steering column cover.

  4. INSTALL LOWER STEERING COLUMN COVER


    1. A01EKV0

      Engage the 2 claws to install the lower steering column cover.

    2. Install the 2 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  6. ADJUST SPIRAL CABLE


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01EMI1

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A01EKJ1E01
      Text in Illustration
      *1 Alignment Mark

      Rotate the spiral cable clockwise approximately 2.5 turns to align the alignment marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  7. INSTALL STEERING WHEEL ASSEMBLY


    1. A01EK6NE01
      Text in Illustration
      *1 Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect each connector to the spiral cable sub-assembly.

  8. INSTALL STEERING PAD


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01EKGZE01
      Text in Illustration
      *1 Airbag Connector
      *2 Horn Connector
      *3 Airbag Connector Lock

      Connect the 2 airbag connectors to the steering pad.

      Note


      • When connecting any airbag connector, take care not to damage the airbag wire harness.

      • Be sure to only connect the connectors to each corresponding color.

    4. Push in the 2 airbag connector locks to install the 2 airbag connectors.

    5. Connect the horn connector to the steering pad.

    6. A01EJV9

      Push the steering pad to engage the 3 pins carefully.

      Note


      • Make sure that the pins are securely inserted into the steering holes.

      • Make sure to engage the 2 upper pins first.

      • Make sure that the steering pad is securely installed.

  9. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. Engage the claw and guide to install the lower No. 3 steering wheel cover.

  10. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. Engage the claw and guide to install the lower No. 2 steering wheel cover.

  11. INSPECT STEERING WHEEL CENTER POINT

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. INSPECT STEERING PAD


    1. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  14. INSPECT SRS WARNING LIGHT

    Click here