UNLOCK WARNING SWITCH REMOVAL


  1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    1. A01ELFH

      Disengage the claw and guide to remove the lower No. 3 steering wheel cover.

  4. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    1. A01EMOX

      Disengage the claw and guide to remove the lower No. 2 steering wheel cover.

  5. REMOVE STEERING PAD

    CAUTION:

    When storing the steering pad, keep the airbag deployment side facing upward.


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01EL3QE01
      Text in Illustration
      *1 Torsion Spring

      Using a screwdriver, push up the torsion spring to disengage the pin.

      Tech Tips

      Insert the screwdriver from the installation hole of the lower No. 3 steering wheel cover.

    4. A01EM14E01
      Text in Illustration
      *1 Torsion Spring

      Using a screwdriver, push in the 2 torsion springs to disengage the 2 pins.

      Note

      Do not drop the steering pad.

      Tech Tips

      Insert the screwdriver from the installation holes in the lower No. 3 steering wheel cover and lower No. 2 steering wheel cover.

    5. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

      Note

      When removing the steering pad, do not pull the airbag wire harness.

    6. A01EJQNE01
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Horn Connector
      *4 Airbag Connector Lock

      Disconnect the horn connector from the steering pad.

    7. Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.

    8. Disconnect the 2 airbag connectors to remove the steering pad.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  6. REMOVE STEERING WHEEL ASSEMBLY


    1. A01EK6NE01
      Text in Illustration
      *1 Matchmark

      Remove the steering wheel assembly set nut.

    2. Put matchmarks on the steering wheel assembly and the steering main shaft.

    3. Disconnect each connector from the spiral cable sub-assembly.

    4. A01ELDDE01
      Text in Illustration
      *1 Turn
      *2 Hold

      Using SST, remove the steering wheel assembly.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05070 )

      Note


      • Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

      • Do not rotate the spiral cable with the battery connected and the ignition switch ON.

      • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

  7. REMOVE LOWER STEERING COLUMN COVER


    1. A01EKV0

      Remove the 2 screws.

    2. Push the right and left sides of the lower steering column cover, and disengage the 2 claws to remove the lower steering column cover.

  8. REMOVE UPPER STEERING COLUMN COVER


    1. A01EJEM

      Disengage the claw.

    2. A01EK5A

      Disengage the 4 clips and 2 guides to remove the upper steering column cover.

  9. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

    2. A01EMNGE01
      Text in Illustration
      *1 Clamp
      *2 Claw

      Using pliers, expand the clamp.

    3. While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.

      Note


      • Do not replace the spiral cable with the battery connected and the ignition switch on.

      • Do not rotate the spiral cable without the steering wheel with the battery connected and the ignition switch on.

      • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

      • Do not remove the steering sensor from the spiral cable.

  10. REMOVE UNLOCK WARNING SWITCH


    1. A01EL0Y

      Disconnect the connector.

    2. Insert the key into the ignition key cylinder.

    3. A01EL18

      Disengage the 2 claws and remove the unlock warning switch from the steering column upper bracket.