CAN COMMUNICATION SYSTEM, Diagnostic DTC:U0208

DTC Code DTC Name
U0208 Lost Communication with "Seat Control Module A"

DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0208 No communication from the position control ECU and switch assembly.

  • Position control ECU and switch assembly branch wire or connector

  • Power source circuit of position control ECU and switch assembly

  • Position control ECU and switch assembly

WIRING DIAGRAM

A01EKYGE05

INSPECTION PROCEDURE

Note


  • Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

  • Turn the ignition switch off before inspecting CAN bus wires for a ground short.

  • After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.

  • Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

Tech Tips


  • Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE


  1. RECONFIRM DTC OUTPUT


    1. Reconfirm DTCs.

      Tech Tips

      If CAN MS bus DTC U1002 is output from the main body ECU (driver side junction block assembly) (GTS display: Main Body), troubleshoot for U1002 and check for malfunctions in the CAN MS bus circuit.

      Result
      Result Proceed to
      U1002 is not output from main body ECU (driver side junction block assembly) (GTS display: Main Body) A
      U1002 is output from main body ECU (driver side junction block assembly) (GTS display: Main Body) B

    B

    GO TO CIRCUITS INDICATED BY OUTPUT DTCS Click here

    A

  2. CHECK FOR OPEN IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH WIRE)


    1. Turn the ignition switch off.

    2. A01EJMFE76
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Position Control ECU and Switch Assembly)

      Disconnect the position control ECU and switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T11-8 (CANP) - T11-7 (CANN) Ignition switch off 54 to 69 Ω

    NG

    REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH WIRE)

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    1. A01EJJHE23
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Position Control ECU and Switch Assembly)

      Disconnect the position control ECU and switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      T10-6 (+B) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    OK

  4. CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    1. A01EJJHE24
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Position Control ECU and Switch Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T10-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

    OK

    REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY Click here