NAVIGATION SYSTEM (for Navigation Receiver Type) Microphone Circuit between Microphone and Navigation Receiver Assembly

DESCRIPTION

• The navigation receiver assembly and inner rear view mirror assembly (amplifier microphone assembly) are connected to each other using the microphone connection detection signal lines.

• Using this circuit, the navigation receiver assembly sends power to the inner rear view mirror assembly (amplifier microphone assembly), and the inner rear view mirror assembly (amplifier microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY))

   
   

   1. Disconnect the E40 navigation receiver assembly connector.

   2. Disconnect the P12 inner rear view mirror assembly (amplifier microphone assembly) connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition E40-4 (MACC) - P12-9 (ACC) Always Below 1 Ω E40-5 (MIN+) - P12-11 (MIC+) Always Below 1 Ω E40-19 (MIN-) - P12-12 (MIC-) Always Below 1 Ω E40-6 (SNS2) - P12-10 (SGND) Always Below 1 Ω E40-4 (MACC) - Body ground Always 10 kΩ or higher E40-5 (MIN+) - Body ground Always 10 kΩ or higher E40-19 (MIN-) - Body ground Always 10 kΩ or higher E40-18 (SGND) - Body ground Always 10 kΩ or higher E40-6 (SNS2) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

2. INSPECT NAVIGATION RECEIVER ASSEMBLY

   
   

   1. Reconnect the E40 navigation receiver assembly connector.

   2. Reconnect the P12 inner rear view mirror assembly (amplifier microphone assembly) connector.

   3. 

      Text in Illustration

      *a	Component with harness connected (Navigation Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition E40-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition E40-18 (SGND) - Body ground Always Below 1 Ω E40-19 (MIN-) - Body ground Always Below 1 Ω

   
   

   NG

   REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

   OK

3. INSPECT INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY)

   
   

   1. Remove the inner rear view mirror assembly (amplifier microphone assembly).

   2. 

      Text in Illustration

      *a	Component without harness connected (Inner Rear View Mirror Assembly (Amplifier Microphone Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 10 (SGND) - 12 (MIC-) Always Below 1 Ω

   
   

   NG

   REPLACE INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY) Click here

   OK

4. INSPECT INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY)

   
   

   1. Reconnect the E40 navigation receiver assembly connector.

   2. Reconnect the P12 inner rear view mirror assembly (amplifier microphone assembly) connector.

   3. Turn the ignition switch to ACC.

   4. 

      Text in Illustration

      *a	Component with harness connected (Inner Rear View Mirror Assembly (Amplifier Microphone Assembly))

      Connect an oscilloscope to terminals 11 (MIC+) and 12 (MIC-) of the P12 inner rear view mirror assembly (amplifier microphone assembly) connector.

   5. Check the waveform of the inner rear view mirror assembly (amplifier microphone assembly) using the oscilloscope.

      Result
      Result Proceed to A waveform synchronized with the voice input to the inner rear view mirror assembly (amplifier microphone assembly) is output A A waveform synchronized with the voice input to the inner rear view mirror assembly (amplifier microphone assembly) is not output B

   
   

   B

   REPLACE INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY) Click here

   A

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here