NAVIGATION SYSTEM (for Navigation Receiver Type), Diagnostic DTC:B15D3

DTC Code DTC Name
B15D3 Stereo Component Amplifier Disconnected

DESCRIPTION

The navigation receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly.

DTC No. DTC Detection Condition Trouble Area
B15D3

When either condition below is met:


  • Stereo component amplifier assembly is/was not connected while the ignition switch is/was ON or ACC.

  • Communication between the master unit and the stereo component amplifier assembly is/was not possible when the engine is/was started.

  • Stereo component amplifier assembly power source circuit

  • AVC-LAN circuit between navigation receiver assembly and stereo component amplifier assembly

  • Stereo component amplifier assembly

  • Navigation receiver assembly

  • Harness or connector

Tech Tips


  • Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

  • The navigation receiver assembly is the master unit.

WIRING DIAGRAM

A01EKJPE17

INSPECTION PROCEDURE

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System Click here.

PROCEDURE


  1. CHECK DTC


    1. If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

      Result
      Result Proceed to
      DTC B15C3 is not output. A
      DTC B15C3 is output. B

    B

    GO TO DTC "B15C3" Click here

    A

  2. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result
      Result Proceed to
      Optional components (including associated wiring) are installed. A
      Optional components (including associated wiring) are not installed. B

      Tech Tips


      • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

      • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


    B

    CHECK DTC Click here

    A

  3. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note

      Do not remove optional components or associated wiring without the permission of the customer.


    NEXT

  4. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.

    NG

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE) Click here

    OK

    END

  5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)


    1. Disconnect the E13 and E14 stereo component amplifier assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E13-2 (GND) - Body ground Always Below 1 Ω
      E13-6 (GND2) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E13-1 (+B) - E13-2 (GND) Always 11 to 14 V
      E13-3 (+B2) - E13-2 (GND) Always 11 to 14 V
      E14-12 (ACC) - E13-2 (GND) Ignition switch ACC 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the E40 navigation receiver assembly connector.

    2. Disconnect the E14 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E40-7 (TX1+) - E14-8 (TX+) Always Below 1 Ω
      E40-8 (TX1-) - E14-7 (TX-) Always Below 1 Ω
      E40-7 (TX1+) - Body ground Always 10 kΩ or higher
      E40-8 (TX1-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY


    1. Replace the stereo component amplifier assembly Click here.

    2. Clear the DTCs Click here.

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

    OK

    END