LUGGAGE SPEAKER INSTALLATION


  1. INSTALL REAR NO. 3 SPEAKER ASSEMBLY


    1. Install the rear No. 3 speaker assembly with the 2 bolts.

    2. Engage the clamp.

  2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish assembly LH.

    2. Insert the upper edge of the roof side inner garnish assembly LH into the roof headlining. Lift the lower edge of the garnish up and push it in over the 3 stud bolts while ensuring ample clearance.

      Note

      Do not damage the roof headlining assembly or roof side inner garnish assembly.

    3. Engage the 10 clips to install the roof side inner garnish assembly LH with the bolt.

      A01EIX2E01
      Text in Illustration
      *1 Stud Bolt - -
    4. A01ELU9E01
      Text in Illustration
      *1 Protective Tape

      Remove the applied protective tape.

    5. w/ Rear Speaker:


      1. Disconnect the connector.

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Engage the 7 claws and the 5 clips.

    3. Install the deck trim side panel assembly LH with the bolt and clip.

      A01EJPS

  4. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A01EKS4E01
      Text in Illustration
      *1 Protruding Part

      Connect the floor anchor end of the rear seat outer belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding part of the floor panel.

  5. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. A01EJ2H

      Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  6. INSTALL RECLINING REMOTE CONTROL BEZEL LH


    1. A01EKL1

      Engage the 3 claws to install the reclining remote control bezel LH.

  7. INSTALL REAR SEAT ASSEMBLY LH

    Click here

  8. INSTALL REAR FLOOR FINISH PLATE


    1. A01EJJN

      Engage the 4 clips and 2 claws to install the rear floor finish plate.

  9. INSTALL REAR SEAT SUB FLOOR PANEL ASSEMBLY


    1. A01ELM5

      Engage the 2 guides, 2 claws and 5 clips to install the rear seat sub floor panel assembly.

  10. INSTALL NO. 1 DECK BOARD


    1. A01EK32

      Engage the 6 clips to install the No. 1 deck board.

  11. INSTALL DECK SIDE TRIM BOX RH


    1. A01EIQE

      Install the deck side trim box RH with the 4 clips.

  12. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A01EMLZ

      Engage the 2 guides to install the No. 2 deck board sub-assembly.

  13. INSTALL DECK SIDE TRIM BOX LH


    1. A01ELW2

      Install the deck side trim box LH with the 3 clips.

  14. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A01EINV

      Engage the 2 guides to install the No. 3 deck board sub-assembly.

  15. INSTALL DECK BOARD ASSEMBLY


    1. A01EL2J

      Engage the 2 guides to install the deck board assembly.

  16. INSTALL TONNEAU COVER ASSEMBLY


    1. Install the tonneau cover assembly.

  17. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EL3EE02
      Text in Illustration
      *1 Alignment mark (Purple)

      Align the alignment mark (Purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  18. INSTALL REAR DOOR SCUFF PLATE LH


    1. A01EMQ6

      Engage the 2 clips and 6 claws to install the rear door scuff plate LH.