PARKING BRAKE ASSEMBLY DISASSEMBLY

Tech Tips


  • Use the same procedure for the RH side and the LH side.

  • The procedure listed below is for the LH side.


  1. REMOVE REAR WHEEL

  2. REMOVE REAR AXLE SHAFT NUT (for AWD)

    Note

    Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

    Tech Tips

    Click here.

  3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    1. A01EM42

      Remove the 2 bolts and rear disc brake caliper assembly.

      Note


      • Do not disconnect the rear brake flexible hose from the rear disc brake caliper assembly.

      • Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging down by the rear brake flexible hose.

  4. REMOVE REAR DISC


    1. A01ELX3E01
      Text in Illustration
      *1 Matchmark

      Put matchmarks on the rear disc and rear axle hub.

      Tech Tips

      The above step is not necessary when the rear disc will be replaced.

    2. A01EL4A

      Release the parking brake and remove the rear disc.

      Tech Tips

      If the rear disc cannot be removed easily, insert a screwdriver through the service hole to loosen the parking brake shoes by turning the adjusting screw.

  5. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01ELOR

      Remove the 2 No. 1 parking brake shoe return tension springs.

  6. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A01ELNW

      Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.

  7. REMOVE PARKING BRAKE SHOE STRUT


    1. A01EM0F

      Remove the parking brake shoe strut and the parking brake shoe strut compression spring.

  8. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A01EJ57

      Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.

  9. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A01EL8K

      Remove the parking brake shoe adjusting screw set.

  10. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A01EK7L

      Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.

  11. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01EM34

      Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.

  12. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER


    1. A01EL0R

      Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.

      Note

      Be careful not to damage the No. 3 parking brake cable assembly.

  13. REMOVE PARKING BRAKE SHOE LEVER


    1. A01EMRN

      Remove the C-washer, shim and the parking brake shoe lever from the No. 2 parking brake shoe assembly.

      Tech Tips

      The shim is installed only when a clearance adjustment between the parking brake lever and parking brake shoe C-washer is necessary. Therefore, some models may have no shim.

  14. REMOVE PARKING BRAKE SHOE GUIDE PLATE SET BOLT


    1. A01EMBL

      Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.

  15. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)


    1. A01EJS3

      Remove the No. 1 parking brake shoe hold down spring pin.

  16. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for AWD)


    1. A01EML8

      Remove the No. 2 parking brake shoe hold down spring pin.

  17. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD)

    Note

    Perform this procedure only when the No. 2 parking brake shoe hold down spring pin is replaced.

    Tech Tips

    Click here.

  18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for AWD)

    Note

    Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

    Tech Tips

    Click here.

  19. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)


    1. A01EJTV

      Remove the No. 2 parking brake shoe hold down spring pin.

  20. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for AWD)


    1. A01ELWT

      Remove the No. 1 parking brake shoe hold down spring pin.