YAW RATE AND ACCELERATION SENSOR REMOVAL


  1. REMOVE FRONT SEAT ASSEMBLY LH

    Tech Tips

    Refer to the procedure up to Remove Front Seat Assembly Click here

  2. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Perform the same procedure as the LH side.

  3. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01EJVQE01

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 6 clips.

    2. Disconnect the connectors and remove the upper console panel sub-assembly.

  4. REMOVE NO. 2 CONSOLE BOX CARPET


    1. A01EKN6

      Remove the No. 2 console box carpet.

  5. REMOVE CONSOLE BOX ASSEMBLY


    1. A01EKRE

      Remove the 2 bolts.

    2. A01EKCR

      Remove the screw and 2 clips.

    3. A01EJXQ

      Disengage the 2 claws.

    4. Disconnect the connectors and remove the console box assembly.

  6. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    1. A01EK00

      Remove the screw.

    2. A01ELRWE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    3. Using a moulding remover, disengage the 2 clips and 4 guides as shown in the illustration.

    4. Disconnect the connector and remove the air conditioning control assembly.

  7. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01ELE9

      Disengage the 3 clips, 7 claws and guide, and remove the front door scuff plate LH.

  8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01EJEA

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  9. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A01EKDA

      Remove the bolt <C> and screw <E> or <F>.

    2. Disengage the claw and 9 clips.

    3. Disconnect the connectors.

    4. A01EITG

      Disconnect the connector and aspirator duct.

    5. A01EJS4

      Disconnect the hood lock control cable and remove the lower No. 1 instrument panel finish panel.

  10. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  11. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  12. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01EMCD

      Push the 3 claws in the direction indicated by the arrow to disengage them.

    2. Disengage the guide and remove the No. 2 instrument panel under cover sub-assembly.

  13. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01EJR6

      Remove the bolt <C> and 4 screws <E> or <F>.

    2. A01EIMR

      Disengage the claw, 3 clips and 5 guides.

    3. Disconnect the connectors and remove the lower instrument panel sub-assembly.

  14. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01EK0N

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  15. REMOVE POSITION INDICATOR HOUSING ASSEMBLY


    1. Move the shift lever to N.

    2. A01ELXD

      Disconnect the connector.

    3. Disengage the 3 clips and remove the position indicator housing assembly.

  16. REMOVE CONSOLE BOX SUB-ASSEMBLY


    1. A01EK7A

      Remove the 2 screws <E> or <F>.

    2. Using a clip remover, remove the clip.

    3. Disconnect the connector.

    4. Disengage the 2 clamps.

    5. A01ELB3

      Disengage the 2 claws and 4 clips and remove the console box sub-assembly.

  17. REMOVE NO. 4 CENTER MEMBER FLOOR REINFORCE SUB-ASSEMBLY


    1. Turn back the floor carpet.

    2. A01EKRFE01

      Remove the 7 bolts and No. 4 center member floor reinforce sub-assembly.

  18. REMOVE YAW RATE AND ACCELERATION SENSOR


    1. Disconnect the connector from the yaw rate and acceleration sensor with bracket.

    2. A01EKX8E01

      Remove the 2 bolts and yaw rate and acceleration sensor with bracket.

    3. A01EKLUE01

      Remove the 2 nuts and yaw rate and acceleration sensor from the bracket.