REAR SPEED SENSOR (for AWD) REMOVAL

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.

  • If the sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR WHEEL

  3. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01EMQ6

      Disengage the 2 clips and 6 claws, and remove the rear door scuff plate LH.

  4. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EJBD

      Remove the rear door opening trim weatherstrip LH.

  5. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  6. REMOVE DECK BOARD ASSEMBLY


    1. A01EL2J

      Disengage the 2 guides and remove the deck board assembly.

  7. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A01EINV

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  8. REMOVE DECK SIDE TRIM BOX LH


    1. A01ELW2

      Remove the 3 clips and remove the deck side trim box LH.

  9. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A01EMLZ

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  10. REMOVE DECK SIDE TRIM BOX RH


    1. A01EIQE

      Remove the 4 clips and remove the deck side trim box RH.

  11. REMOVE NO. 1 DECK BOARD


    1. A01EK32

      Disengage the 6 clips and remove the No. 1 deck board.

  12. REMOVE REAR SEAT SUB FLOOR PANEL ASSEMBLY


    1. A01ELM5

      Disengage the 2 claws, 2 guides and 5 clips, and remove the rear seat sub floor panel assembly.

  13. REMOVE REAR FLOOR FINISH PLATE


    1. A01EJJN

      Disengage the 2 claws and 4 clips, and remove the rear floor finish plate.

  14. REMOVE RECLINING REMOTE CONTROL BEZEL LH


    1. A01EIRXE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 3 claws and remove the reclining remote control bezel LH.

      Tech Tips

      Tape the screwdriver tip before use.

  15. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


    1. A01EJ2H

      Remove the 2 bolts.

    2. Disengage the 2 guides and remove the 2 luggage hold belt striker assemblies.

  16. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A01EIYD

      Remove the bolt and disconnect the floor end of the rear seat outer belt assembly.

  17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the bolt and clip.

    2. Disengage the 7 claws and 5 clips.

    3. Disconnect the connector and remove the deck trim side panel assembly LH.

      A01EJPS

  18. REMOVE REAR SPEED SENSOR


    1. A01ELLBE01
      Text in Illustration
      *1 Grommet

      Disconnect the rear speed sensor connector.

    2. A01EKY5E01
      Text in Illustration
      *1 No. 2 Clamp
      *2 No. 1 Clamp

      Disconnect the grommet of the rear speed sensor wire from the hole of the wheel house.

    3. Remove the 2 bolts, No. 1 clamp and No. 2 clamp from the body and absorber.

    4. A01ELYI

      Remove the bolt and rear speed sensor from the carrier.

      Note

      Keep the sensor tip and rear speed sensor installation hole free from foreign matter.