CRUISE CONTROL SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Cruise Control / Data List.

    5. Read the Data List according to the display on the GTS.

      Cruise Control (ECM)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      CCS Vehicle Spd Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
      CCS Mem Vehicle Spd Cruise control memorized speed / Min.: 0 km/h (0 mph), Max.: 200 km/h (125 mph) Stored vehicle speed -
      Throttle Opening Angle Throttle opening angle / Min.: 0°, Max.: 125° Demanded throttle angle -
      Cruise Control Cruise control system active condition / ON or OFF

      ON: Cruise control activated

      OFF: Cruise control deactivated

      		 -
      Main SW M-CPU Main switch signal (Main CPU) / ON or OFF

      ON: Main switch on

      OFF: Main switch off

      		 -
      CCS Ready M-CPU Cruise control system standby condition (Main CPU) / ON or OFF Each time main switch is pushed, display changes between ON and OFF -
      CCS Indicator M-CPU CRUISE main indicator signal (Main CPU) / ON or OFF

      ON: CRUISE main indicator light on

      OFF: CRUISE main indicator light off

      		 -
      Cancel Switch CANCEL switch signal / ON or OFF

      ON: CANCEL switch on

      OFF: CANCEL switch off

      		 -
      SET/COAST Switch - / SET switch signal / ON or OFF

      ON: - / SET switch on

      OFF: - / SET switch off

      		 -
      RES/ACC Switch + / RES switch signal / ON or OFF

      ON: + / RES switch on

      OFF: + / RES switch off

      		 -
      Stp Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Cruise Operation Status Park/neutral position switch signal (D position) / ON or OFF

      ON: Shift lever in D

      OFF: Shift lever not in D

      		 -

      Tech Tips


      • If any DTCs are output, the value for a measurement item may be incorrect.

      • If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Combination Meter / Active Test.

    5. Perform Active Test according to the display on the GTS.

      Tech Tips

      The ignition switch must be turned to ON to proceed with the Active Test using the GTS.

      Combination Meter
      Tester Display Test Part Control Range Diagnostic Note
      Indicat. Lamp Cruise CRUISE main indicator light OFF or ON Confirm that the vehicle is stopped with the engine idling
      Indicat. SET SET indicator light OFF or BLINK Confirm that the vehicle is stopped with the engine idling