CANISTER REMOVAL


  1. REMOVE NO. 1 FLOOR UNDER COVER


    1. A01EKZZ

      Disengage the 4 nuts and clip, and remove the No. 1 floor under cover.

      Text in Illustration
      A01EM1I Nut (attached to under cover)

      Tech Tips

      Rotate the clip to disengage it. The 4 nuts will remain attached to the No. 1 floor under cover.

  2. REMOVE CHARCOAL CANISTER ASSEMBLY


    1. Disconnect the vent line tube from the charcoal canister assembly.

      A01EMNDE01
      Text in Illustration
      *1 Tube Connector *2 O-ring
      *3 Retainer *4 Pipe (Charcoal Canister Assembly)
      A01EM1I Pinch A01EMIT Pull

      Note


      • Remove any dirt or foreign matter on the tube connector before performing this work.

      • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe.

      • Perform this work by hand. Do not use any tools.

      • Do not forcibly bend, twist or turn the vent line tube.

      • Protect the disconnected parts by covering them with plastic bags after disconnecting the vent line tube.

      • If the tube connector and pipe are stuck, push and pull on them to release.

      Tech Tips

      Do not remove the retainer.

    2. A01ELWGE01
      Text in Illustration
      *1 Tube Connector
      *2 O-ring
      *3 Pipe (charcoal canister leak detection pump sub-assembly)
      A01EM1I Pinch
      A01EMIT Push

      Disconnect the air line tube from the charcoal canister leak detection pump sub-assembly.

      Note


      • Remove any dirt or foreign matter on the tube connector before performing this work.

      • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe.

      • Perform this work by hand. Do not use any tools.

      • Do not forcibly bend, twist or turn the air line tube.

      • Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

      • If the tube connector and pipe are stuck, push and pull on them to release.


      1. Push the air line tube firmly toward the charcoal canister assembly side.

      2. Pinch the tube connector as shown in the illustration.

      3. Pull out the air line tube.

    3. A01EMDD

      Disconnect the purge line hose from the charcoal canister assembly.

    4. Disconnect the connector from the charcoal canister leak detection pump sub-assembly.

    5. A01EIXR

      Remove the 4 nuts.

    6. Separate the 2 clips from the body to remove the charcoal canister assembly.

  3. REMOVE CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY


    1. Before removing the charcoal canister leak detection pump sub-assembly, clean the canister by blowing air into it to ensure that the canister is free of foreign matter.

      Note


      • Make sure to clean the canister using only air.

      • Do not use gasoline, thinners or solvents.

    2. A01EJ8EE01
      Text in Illustration
      *1 Protective Tape

      While disengaging the 2 claws as shown in the illustration, push the charcoal canister leak detection pump sub-assembly out using a screwdriver to remove it.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Check if the canister contains foreign matter such as mud or water.


      1. A01EKAP

        Visually check that the inside of the canister is free of foreign matter.

      2. Hold the canister upside down to make sure that the canister is free of foreign matter.

        If the canister contains foreign matter, replace the canister.