CYLINDER HEAD REPLACEMENT


  1. REPLACE INTAKE VALVE GUIDE BUSH


    1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    2. Place the cylinder head on wooden blocks.

    3. A01ELIJE01

      Using SST and a hammer, tap out the valve guide bush.

      SST
      09201-01055
      09950-70010   ( 09951-07100 )
    4. A01EM1F

      Using a caliper gauge, measure the bush bore diameter of the cylinder head.

      Standard bush bore diameter
      10.285 to 10.306 mm (0.405 to 0.406 in.)

      If the bush bore diameter of the cylinder head is between 10.285 and 10.306 mm (0.405 and 0.406 in.), proceed to the next step.

      If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head

    5. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

    6. Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

      Bush Bore Diameter
      Bush Size Specified Condition
      STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
      O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
      Standard bush length
      41.3 to 41.7 mm (1.626 to 1.642 in.)

    7. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    8. A01EKXXE01

      Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
      Standard protrusion height
      14.8 to 15.2 mm (0.582 to 0.598 in.)
    9. A01EM1L

      Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

      Standard oil clearance
      0.025 to 0.060 mm (0.000984 to 0.00236 in.)

  2. REPLACE EXHAUST VALVE GUIDE BUSH


    1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    2. Place the cylinder head on wooden blocks.

    3. A01EJLRE01

      Using SST and a hammer, tap out the valve guide bush.

      SST
      09201-01055
      09950-70010   ( 09951-07100 )
    4. A01ELWN

      Using a caliper gauge, measure the bush bore diameter of the cylinder head.

      Standard bush bore diameter
      10.285 to 10.306 mm (0.405 to 0.406 in.)

      If the bush diameter of the cylinder head is between 10.285 and 10.306 mm (0.405 and 0.406 in.), proceed to the next step.

      If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.

    5. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

    6. Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

      Bush Bore Diameter
      Bush Size Specified Condition
      STD 10.333 to 10.344 mm (0.4068 in 0.4072 in.)
      O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
      Standard bush length
      46.8 to 47.2 mm (1.843 to 1.858 in.)

    7. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    8. A01EIP6E01

      Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
      Standard protrusion height
      14.2 to 14.6 mm (0.559 to 0.575 in.)
    9. A01EJUS

      Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

      Standard oil clearance
      0.030 to 0.065 mm (0.00118 to 0.00256 in.)

  3. REPLACE RING PIN

    Note

    It is not necessary to remove the ring pin unless it is being replaced.


    1. Remove the ring pins.

    2. A01EJGFE01

      Using a plastic-faced hammer, tap in new ring pins to the cylinder head.

      Standard protrusion height
      6.5 to 7.5 mm (0.256 to 0.295 in.)