SFI SYSTEM, Diagnostic DTC:P2009, P2010

DTC Code DTC Name
P2009 Intake Manifold Runner Control Circuit Low (Bank 1)
P2010 Intake Manifold Runner Control Circuit High (Bank 1)

DESCRIPTION

The ECM activates the DC motor for the tumble control valve, which opens and closes the tumble control valve. The ECM activates the DC motor based on engine speed, coolant temperature, intake air temperature and other conditions.

DTC No. DTC Detection Condition Trouble Area
P2009

Both of the following conditions continue for 1 second (1 trip detection logic):

(a) The output duty of the DC motor for the tumble control valve is 100% or higher.

(b) The current of the DC motor for the tumble control valve is below 0.35 A.

  • Open or short in DC motor for tumble control valve circuit

  • Intake manifold (DC motor for tumble control valve)

  • ECM
P2010

Either of the following conditions continues for 6 times or more (1 trip detection logic):

(a) The motor drive IC is overcurrent.

(b) The motor drive IC overheats.

MONITOR DESCRIPTION

When the voltage of the DC motor deviates from the standard range, the ECM determines that a malfunction has occurred and outputs a DTC.

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) Click here.

  5. Turn the ignition switch off and wait for at least 30 seconds.

  6. Turn the ignition switch to ON and turn the GTS on.

  7. Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.

  8. Check that the engine coolant temperature is 60°C (140°F) or higher.

  9. Wait approximately 10 seconds.

  10. Enter the following menus: Powertrain / Engine / Trouble Codes.

  11. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  13. Input the DTC: P2009 or P2010.

  14. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P2004 Click here.

INSPECTION PROCEDURE

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)


    1. Inspect the intake air control valve actuator (for tumble control valve) Click here.


    NG

    REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE) Click here

    OK

  2. INSPECT INTAKE MANIFOLD (TUMBLE CONTROL VALVE OPERATION)


    1. Inspect the intake manifold Click here.


    NG

    REPLACE INTAKE MANIFOLD Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR CONTROL VALVE ACTUATOR)


    1. Disconnect the ECM connector.

    2. Disconnect the intake air control valve actuator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B58-3 (IA1-) - U3-4 (M-) Always Below 1 Ω
      B58-4 (IA1+) - U3-5 (M+) Always Below 1 Ω
      B58-3 (IA1-) or U3-4 (M-) - Body ground Always 10 kΩ or higher
      B58-4 (IA1+) or U3-5 (M+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2009 OR P2010)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON and turn the GTS on.

    7. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    8. Enter the following menus: Powertrain / Engine / Trouble Codes.

    9. Read the DTCs.

      Result
      Result Proceed to
      DTC P2009 or P2010 is output A
      DTC is not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

    REPLACE ECM Click here